- Idle air control (IAC) valve moan - occurs on throttle tip-out
|
- IAC valve is contaminated with oil
|
|
- Accessory drive belt chirp - occurs at idle or high idle, cold or hot. Most common occurrence is during humid weather
|
- Accessory drive belt worn, or pulley is misaligned or loose
|
|
- Accessory drive bearing hoot - occurs at idle or high idle in cold temperatures of approximately +4°C (+40°F) or colder at the first start of the day
|
- Accessory drive idler or tensioner pulley bearing is experiencing stick/slip between ball bearings and the bearing race
|
|
- Power steering moan - occurs at high idle and possibly at idle during the first cold start of the day in temperatures of approximately -18°C (0°F) or colder. Noise can even be a severe screech for less than one minute in very cold temperatures of approximately -29°C (-20°F) or colder
|
- High fluid viscosity or plugged reservoir screen in the power steering reservoir starves pump causing cavitation
|
|
- Generator whine - during high electrical loads at idle or high idle, a high pitch whine or moan is emitted from the generator
|
- Generator electrical field noise
|
- Using an EngineEAR, PROBE near the generator housing. LISTEN for changes in the noise level while changing the electrical loads (such as rear defrost, headlamps, etc.). CARRY OUT a generator load test. If the system passes the load test, the noise is from the generator bearings. INSTALL a new generator. REFER to GENERATOR AND REGULATOR
.
|
- Drumming noise - occurs inside the vehicle during idle or high idle, hot or cold. Very low-frequency drumming is very rpm dependent
|
- Exhaust system vibration excites the body resonances inducing interior noise
- Engine vibration excites the body resonances inducing interior noise
|
|
- Hissing noise - occurs during idle or high idle that is apparent with the hood open
|
- Vacuum leak or idle air control (IAC) valve flow noise
|
- Use the Ultrasonic Leak Detector/EngineEAR to locate the source. Scan the air intake system from the inlet to each cylinder intake port. DISCARD the leaking parts, and INSTALL a new component.
|
- Idle air control (IAC) valve flow noise
|
|
- Vehicles with a plastic intake manifold
|
- Acceptable condition. Some plastic manifolds exhibit this noise, which is the effect of the plastic manifold.
|
- Automatic transmission buzz or hiss
|
- Incorrect driveline angles
|
|
- Worn or damaged main control solenoids or valves
|
|
- Manual transmission clutch release bearing whine. A change in noise pitch or loudness while applying the clutch pedal
|
- Worn clutch release bearing
|
- INSTALL a new clutch release bearing. REFER to CLUTCH
.
|
- Heating, vacuum, and air conditioning (HVAC) system chirp - most audible inside the vehicle. Listen for a change in the noise pitch or loudness while changing the HVAC system blower speed
|
- Damaged or worn HVAC blower bearing
|
|
- Air conditioning (A/C) clutch ticking - occurs when the compressor clutch engages
|
- Acceptable noise
- Incorrect air gap
|
- LISTEN to the clutch to determine if the noise occurs with clutch engagement. A small amount of noise is acceptable. If the noise is excessive, CHECK the A/C clutch air gap. INSPECT the A/C clutch for wear or damage. INSTALL a new clutch as necessary. REFER to CLIMATE CONTROL
.
|
- Intermittent rattle or scraping/rubbing noise
|
- Loose exhaust heat shield(s)
|
- INSPECT the exhaust system for loose parts using a glove or clamps to verify the cause. REPAIR as necessary. REFER to EXHAUST SYSTEM
.
|
- Wiring, hose or other part interfering with accessory drive, drive belt or pulley
|
- INSPECT the accessory drive system closely. VERIFY there is adequate clearance to all rotating components. REPAIR as necessary.
|
- Engine ticking or knocking noise - occurs during idle or high idle during the first cold start of the day
|
- Piston noise or valve train noise (bled down lifter/lash adjuster)
|
|
- A continuous, speed-dependent rattle from the engine - occurs during idle or high idle during the first cold start of the day and disappears as the engine warms up
|
- Piston noise or valve train noise (bled down lifter/lash adjuster)
|
|
- Idle vibration - a low-frequency vibration (5-20 Hz) or mild shake that is felt through the seat/floorpan
|
|
|
- Engine or torque converter out of balance
|
|
- Idle vibration - a high-frequency vibration (20-80 Hz) or buzz that is felt through the steering wheel or seat
|
- Exhaust system mounts bound up
|
- VERIFY the concern occurs at the engine firing frequency. CHECK that the exhaust system vibrates at the same frequency as the engine. ADD 9-14 kg (20-30 lb.) to the tail pipe to test. CARRY OUT the EXHAUST SYSTEM NEUTRALIZING PROCEDURE .
|
|
|
- INSPECT the body mounts. CARRY OUT a Neutral Engine Run-Up (NERU) Test. REPAIR as necessary.
|
- Power steering lines grounded out
|
- VERIFY that the power steering lines are not contacting the chassis or each other. REPAIR as necessary.
|