LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1345 (Noise, Vibration & Harshness) >> Diagnosis And Testing >> Noise, Vibration and Harshness (NVH) >> Pinpoint Tests >> Pinpoint Test I: Rear Suspension Noise

Pinpoint Test I: Rear Suspension Noise

WARNING: This page is about a different car, the 2006 Mercury Grand Marquis and 2006 Ford Crown Victoria. However, it is still accessible from the selected car via links, so may be relevant.
  1. I1 ROAD TEST THE VEHICLE 
    • Test drive the vehicle.
      • NOTE: An assistant will be needed for this road test.
    • During the road test, drive the vehicle over a rough road. Using ChassisEARs, determine from which area/component the noise is originating.
    • Is there a squeak, creak or rattle noise? 

    Yes  : GO to I2.

    No  : The suspension system is OK. CONDUCT a diagnosis on other suspect systems.

  2. I2 REAR SHOCK ABSORBER/STRUT CHECK 
      WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch. Failure to do so can result in unexpected inflation or deflation of the air springs, which can result in shifting of the vehicle during these operations.
      WARNING: If equipped with fire suppression system, depower the system. For important safety warnings and procedures, refer to FIRE SUPPRESSION SYSTEM .
    • With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to JACKING & LIFTING .
    • Check the rear shock absorber/strut mounts for loose bolts or nuts.
    • Check the rear shock absorbers/struts for damage. Carry out a "bounce check".
    • Are the rear shock absorbers/struts loose or damaged? 

    Yes  : TIGHTEN to specifications if loose. INSTALL new rear shock absorbers/struts if damaged. TEST the system for normal operation. If equipped with fire suppression system, GO to  I6.

    No  : GO to I3.

  3. I3 CHECK THE REAR SPRINGS 
    • Check the rear springs and rear spring mounts/brackets for wear or damage.
    • Are the rear springs or spring mounts/brackets worn or damaged? 

    Yes  : REPAIR or INSTALL new components as necessary. TEST the system for normal operation. If equipped with fire suppression system, GO to  I6.

    No  : GO to I4.

  4. I4 CHECK THE CONTROL ARMS/TRAILING ARMS 
    • Inspect the control arm/trailing arm bushings for wear or damage. Check for loose control arm/trailing arm bolts.
    • Inspect for twisted or bent control arm/trailing arms.
    • Are the control arm/trailing arms loose, damaged or worn? 

    Yes  : REPAIR or INSTALL new components as necessary. TEST the system for normal operation. If equipped with fire suppression system, GO to  I6.

    No  : GO to I5.

  5. I5 CHECK THE STABILIZER BAR/TRACK BAR 
    • Check the stabilizer bar/track bar bushings and links for damage or wear.
    • Check the stabilizer bar/track bar for damage.
    • Check for loose or damaged stabilizer bar isolators or brackets.
    • Are the stabilizer bar/track bar components loose, worn or damaged? 

    Yes  : REPAIR or INSTALL new components as necessary. TEST the system for normal operation. If equipped with fire suppression system, GO to I6.

    No  : Suspension system OK. CONDUCT diagnosis on other suspect systems. If equipped with fire suppression system, GO to I6.

  6. I6 REPOWER THE FIRE SUPPRESSION SYSTEM 
    WARNING: If equipped with fire suppression system, repower the system. For important safety warnings and procedures, refer to FIRE SUPPRESSION SYSTEM .
    • Verify that the fire suppression system is repowered. For additional information, refer to FIRE SUPPRESSION SYSTEM .
    • If the fire suppression system repowered? 

    Yes  : Fire suppression system repowering is complete.

    No  : REFER to FIRE SUPPRESSION SYSTEM for fire suppression system depowering and repowering procedure.

scientia non olet · About LEMON Manuals