LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1110 (Supplemental Inflatable Restraint System) >> Diagnosis And Testing >> Pinpoint Tests - Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Test T: LFC 24, 25, 31 or 32 DTC B2294 - Restraint System - Curtain Fault >> Testing

Pinpoint Test T: LFC 24, 25, 31 or 32 DTC B2294 - Restraint System - Curtain Fault: Testing

WARNING: This page is about a different car, the 2005 Mercury Montego, 2005 Ford Freestyle, and 2005 Ford Five Hundred. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough Inspection and Verification before proceeding with the Pinpoint Test.
NOTE: Safety canopy modules equipped on Five Hundred and Montego vehicles have a single squib (safety canopy module squib 1 only). Safety canopy modules equipped on Freestyle vehicles have a dual squib (safety canopy module squib 1 and safety canopy module squib 2).
  1. T1 CHECK FOR A HARD OR INTERMITTENT DTC 
    WARNING: Restraint system diagnostic tools are for service only. Tools must be removed prior to operating the vehicle over the road. Failure to remove restraint system diagnostic tools could result in injury and possible violation of vehicle safety standards.
    WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow these instructions may result in the inadvertent deployment of the safety canopy and risk of personal injury.
    WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.
    WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe a pretensioner electrical connector. Doing so could result in pretensioner or air bag deployment and could result in personal injury.
    WARNING: Never probe the electrical connector on a safety canopy module. Doing so can result in safety canopy deployment.
    NOTE: If a seat equipped with a supplemental restraint system (SRS) component is being serviced, the SRS must be depowered.
    NOTE: After diagnosing or repairing an SRS, the restraint system diagnostic tools must be removed before operating the vehicle over the road. 
    NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
    • Enter the following diagnostic mode on the scan tool: Retrieve/Record Continuous DTCs.
    • Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
    • Enter the following diagnostic mode on the scan tool: Flag B2294/Record All Flagged Faults.
    • Was DTC B2294 retrieved during the on-demand self test? 
    1. Yes : Vehicles with safety canopy modules 

      This is a hard fault. The fault condition is still present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test. GO to  T3.

      Vehicles without safety canopy modules 

      This is a hard fault. The fault condition is still present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test. GO to T2.

    2. No  : This is an intermittent fault. The fault condition is not present at this time. GO to  T35.
  2. T2 CHECK THE SAFETY CANOPY MODULE BRIDGE RESISTOR 
    1. Yes  : Using the flagged faults recorded, GO to the appropriate PINPOINT TEST .

      If a flagged fault of "?  " was recorded in Step  T1, multiple faults exist and the entire pinpoint test must be carried out.

      For driver safety canopy module (DFCURTN) with a short to battery (STB) fault, GO to  T28.

      For driver safety canopy module (DFCURTN) with a short to ground (STG) fault, GO to  T29.

      For driver safety canopy module (DFCURTN) with an open circuit (O_CIR) fault, GO to  T30.

      For driver safety canopy module (DFCURTN) with a low resistance (LOWRES) fault, GO to  T32.

    2. No  : Fault corrected. GO to T36.
  3. T3 CHECK THE DRIVER AND PASSENGER SAFETY CANOPY MODULE 
    1. Yes  : Using the flagged faults recorded, GO to the appropriate PINPOINT TEST .

      If a flagged fault of "?  " was recorded in Step  T1, multiple faults exist and the entire pinpoint test must be carried out.

      For driver safety canopy module squib 1 (DFCURTN) with a short to battery (STB) fault, GO to T4.

      For driver safety canopy module squib 1 (DFCURTN) with a short to ground (STG) fault, GO to  T5.

      For driver safety canopy module squib 1 (DFCURTN) with an open circuit (O_CIR) fault, GO to  T6.

      For driver safety canopy module squib 1 (DFCURTN) with a low resistance (LOWRES) fault, GO to  T8.

      For passenger safety canopy module squib 1 (PFCURTN) with a short to battery (STB) fault, GO to  T10.

      For passenger safety canopy module squib 1 (PFCURTN) with a short to ground (STG) fault, GO to  T11.

      For passenger safety canopy module squib 1 (PFCURTN) with an open circuit (O_CIR) fault, GO to  T12.

      For passenger safety canopy module squib 1 (PFCURTN) with a low resistance (LOWRES) fault, GO to  T14.

      For driver safety canopy module squib 2 (DRCURTN) with a short to battery (STB) fault, GO to  T16.

      For driver safety canopy module squib 2 (DRCURTN) with a short to ground (STG) fault, GO to  T17.

      For driver safety canopy module squib 2 (DRCURTN) with an open circuit (O_CIR) fault, GO to  T18.

      For driver safety canopy module squib 2 (DRCURTN) with a low resistance (LOWRES) fault, GO to  T20.

      For passenger safety canopy module squib 2 (PRCURTN) with a short to battery (STB) fault, GO to  T22.

      For passenger safety canopy module squib 2 (PRCURTN) with a short to ground (STG) fault, GO to  T23.

      For passenger safety canopy module squib 2 (PRCURTN) with an open circuit (O_CIR) fault, GO to  T24.

      For passenger safety canopy module squib 2 (PRCURTN) with a low resistance (LOWRES) fault, GO to  T26.

    2. No  : If a flagged fault of "?  " was recorded in Step  T1, multiple faults exist and the entire pinpoint test must be carried out.

      If a fault was flagged against the driver safety canopy module in Step  AB1, INSTALL a new driver safety canopy module. REFER to SAFETY CANOPY MODULE - FREESTYLE  or SAFETY CANOPY MODULE - FIVE HUNDRED, MONTEGO . GO to  T36.

      If a fault was flagged against the passenger safety canopy module in Step  AB1, INSTALL a new passenger safety canopy module. REFER to SAFETY CANOPY MODULE - FREESTYLE  or SAFETY CANOPY MODULE - FIVE HUNDRED, MONTEGO . GO to  T36.

  4. T4 CHECK CIRCUIT 1633 (BK/OG) AND CIRCUIT 1634 (RD/PK) FOR A SHORT TO BATTERY BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE SQUIB 1 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • Repower the system. Do not  prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Key in ON position.
    • For Five Hundred and Montego vehicles,  measure the voltage between driver safety canopy module C9031 pin 1, circuit 1633 (BK/OG), harness side and ground; and between driver safety canopy module C9031 pin 2, circuit 1634 (RD/PK), harness side and ground.
      Fig 1: Checking Circuit 1633 (BK/OG) And Circuit 1634 (RD/PK) For Short To Battery Between RCM And Driver Safety Canopy Module Squib 1
      G03953487Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the voltage between driver safety canopy module C9018 pin 1, circuit 1633 (BK/OG), harness side and ground; and between driver safety canopy module C9018 pin 2, circuit 1634 (RD/PK), harness side and ground.
      Fig 2: Measuring Voltage Between Driver Safety Canopy Module C9018 Pin 1, Circuit 1633 (BK/OG), Harness Side And Ground
      G03989655Courtesy of FORD MOTOR CO.
    • Are the voltages less than 0.2 volt? 
    1. Yes  : GO to  T34.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1633 (BK/OG) or circuit 1634 (RD/PK). GO to  T36.

  5. T5 CHECK CIRCUIT 1633 (BK/OG) AND CIRCUIT 1634 (RD/PK) FOR A SHORT TO GROUND BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE SQUIB 1 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • For Five Hundred and Montego vehicles,  measure the resistance between driver safety canopy module C9031 pin 1, circuit 1633 (BK/OG), harness side and ground; and between driver safety canopy module C9031 pin 2, circuit 1634 (RD/PK), harness side and ground.
      Fig 3: Checking Circuit 1633 (BK/OG) And Circuit 1634 (RD/PK) For Short To Ground Between RCM And Driver Safety Canopy Module Squib 1
      G03953484Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between driver safety canopy module C9018 pin 1, circuit 1633 (BK/OG), harness side and ground; and between driver safety canopy module C9018 pin 2, circuit 1634 (RD/PK), harness side and ground.
      Fig 4: Measuring Resistance Between Driver Safety Canopy Module C9018 Pin 1, Circuit 1633 (BK/OG), Harness Side And Ground
      G03987327Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10,000 ohms? 
    1. Yes  : GO to  T34.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1633 (BK/OG) or circuit 1634 (RD/PK). GO to  T36.

  6. T6 CHECK CIRCUIT 1633 (BK/OG) FOR AN OPEN BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE SQUIB 1 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • For Five Hundred and Montego vehicles,  measure the resistance between RCM C310b pin 3, circuit 1633 (BK/OG), harness side and driver safety canopy module C9031 pin 1, circuit 1633 (BK/OG), harness side.
      Fig 5: Checking Circuit 1633 (BK/OG) For Open Between RCM And Driver Safety Canopy Module Squib 1
      G03989647Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between RCM C310b pin 3, circuit 1633 (BK/OG), harness side and driver safety canopy module C9018 pin 1, circuit 1633 (BK/OG), harness side.
      Fig 6: Measuring Resistance Between RCM C310b Pin 3, Circuit 1633 (BK/OG), Harness Side And Driver Safety Canopy Module C9018 Pin 1
      G03989648Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to T7.
    2. No  : REPAIR circuit 1633 (BK/OG). GO to  T36.
  7. T7 CHECK CIRCUIT 1634 (RD/PK) FOR AN OPEN BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE SQUIB 1 
    • For Five Hundred and Montego vehicles,  measure the resistance between RCM C310b pin 4, circuit 1634 (RD/PK), harness side and driver safety canopy module C9031 pin 2, circuit 1634 (RD/PK), harness side.
      Fig 7: Checking Circuit 1634 (RD/PK) For Open Between RCM And Driver Safety Canopy Module Squib 1
      G03989649Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between RCM C310b pin 4, circuit 1634 (RD/PK), harness side and driver safety canopy module C9018 pin 2, circuit 1634 (RD/PK), harness side.
      Fig 8: Measuring Resistance Between RCM C310b Pin 4, Circuit 1634 (RD/PK), Harness Side And Driver Safety Canopy Module C9018 Pin 2
      G03989650Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to  T34.
    2. No  : REPAIR circuit 1634 (RD/PK). GO to  T36.
  8. T8 CHECK FOR LOW RESISTANCE ON CIRCUIT 1633 (BK/OG) AND CIRCUIT 1634 (RD/PK) BETWEEN THE DRIVER SAFETY CANOPY MODULE SQUIB 1 AND THE RCM 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Restraint System Diagnostic Tool.
    • For Five Hundred and Montego vehicles,  measure the resistance between driver safety canopy module C9031 pin 1, circuit 1633 (BK/OG), and driver safety canopy module C9031 pin 2, circuit 1634 (RD/PK), harness side.
      Fig 9: Checking For Low Resistance On Circuit 1633 (BK/OG) And Circuit 1634 (RD/PK) Between Driver Safety Canopy Module Squib 1 And RCM
      G03989651Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between driver safety canopy module C9018 pin 1, circuit 1633 (BK/OG), and driver safety canopy module C9018 pin 2, circuit 1634 (RD/PK), harness side.
      Fig 10: Measuring Resistance Between Connector Terminals
      G03903697Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to T9.
    2. No  : GO to  T34.
  9. T9 CHECK THE RCM FOR LOW RESISTANCE 
    • Disconnect: RCM C310a and C310b.
    • Measure the resistance between RCM C310b pin 3, component side and pin 4, component side.
      Fig 11: Measuring Resistance Between RCM Connector Terminals
      G04011460Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to  T34.
    2. No  : REPAIR circuit 1633 (BK/OG) and circuit 1634 (RD/PK). GO to  T36.
  10. T10 CHECK CIRCUIT 1635 (OG/LG) AND CIRCUIT 1636 (YE/BK) FOR A SHORT TO BATTERY BETWEEN THE RCM AND THE PASSENGER SAFETY CANOPY MODULE SQUIB 1 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Passenger Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • Repower the system. Do not  prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Key in ON position.
    • For Five Hundred and Montego vehicles,  measure the voltage between passenger safety canopy module C9032 pin 1, circuit 1635 (OG/LG), harness side and ground; and between passenger safety canopy module C9032 pin 2, circuit 1636 (YE/BK), harness side and ground.
      Fig 12: Checking Circuit 1635 (OG/LG) And Circuit 1636 (YE/BK) For Short To Battery Between RCM And Passenger Safety Canopy Module Squib 1
      G03953487Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the voltage between passenger safety canopy module C9019 pin 1, circuit 1635 (OG/LG), harness side and ground; and between passenger safety canopy module C9019 pin 2, circuit 1636 (YE/BK), harness side and ground.
      Fig 13: Measuring Voltage Between Passenger Safety Canopy Module C9019 Pin 1, Circuit 1635 (OG/LG), Harness Side And Ground
      G03989655Courtesy of FORD MOTOR CO.
    • Are the voltages less than 0.2 volt? 
    1. Yes  : GO to  T28.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1635 (OG/LG) or circuit 1636 (YE/BK). GO to  T36.

  11. T11 CHECK CIRCUIT 1635 (OG/LG) AND CIRCUIT 1636 (YE/BK) FOR A SHORT TO GROUND BETWEEN THE RCM AND THE PASSENGER SAFETY CANOPY MODULE SQUIB 1 
    • Key in OFF position.
    • Disconnect: Passenger Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • Measure the resistance between RCM C310b pin 5, circuit 1635 (OG/LG), harness side and ground; and between RCM C310b pin 6, circuit 1636 (YE/BK), harness side and ground.
      Fig 14: Checking Circuit 1635 (OG/LG) And Circuit 1636 (YE/BK) For Short To Ground Between RCM And Passenger Safety Canopy Module Squib 1
      G03946357Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10,000 ohms? 
    1. Yes  : GO to  T34.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1635 (OG/LG) or circuit 1636 (YE/BK). GO to  T36.

  12. T12 CHECK CIRCUIT 1635 (OG/LG) FOR AN OPEN BETWEEN THE RCM AND THE PASSENGER SAFETY CANOPY MODULE SQUIB 1 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Passenger Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • For Five Hundred and Montego vehicles,  measure the resistance between RCM C310b pin 5, circuit 1635 (OG/LG), harness side and passenger safety canopy module C9032 pin 1, circuit 1635 (OG/LG), harness side.
      Fig 15: Checking Circuit 1635 (OG/LG) For Open Between RCM And Passenger Safety Canopy Module Squib 1
      G03989657Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between RCM C310b pin 5, circuit 1635 (OG/LG), harness side and passenger safety canopy module C9019 pin 1, circuit 1635 (OG/LG), harness side.
      Fig 16: Measuring Resistance Between RCM C310B Pin 5, Circuit 1635 (OG/LG), Harness Side And Passenger Safety Canopy Module C9019 Pin 1
      G03989658Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to T13.
    2. No  : REPAIR circuit 1635 (OG/LG). GO to  T36.
  13. T13 CHECK CIRCUIT 1636 (YE/BK) FOR AN OPEN BETWEEN THE RCM AND THE PASSENGER SAFETY CANOPY MODULE SQUIB 1 
    • For Five Hundred and Montego vehicles,  measure the resistance between RCM C310b pin 6, circuit 1636 (YE/BK), harness side and passenger safety canopy module C9032 pin 2, circuit 1636 (YE/BK), harness side.
      Fig 17: Checking Circuit 1636 (YE/BK) For Open Between RCM And Passenger Safety Canopy Module Squib 1
      G03989659Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between RCM C310b pin 6, circuit 1636 (YE/BK), harness side and passenger safety canopy module C9019 pin 2, circuit 1636 (YE/BK), harness side.
      Fig 18: Measuring Resistance Between RCM C310B Pin 6, Circuit 1636 (YE/BK), Harness Side And Passenger Safety Canopy Module C9019 Pin 2
      G03989660Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to  T34.
    2. No  : REPAIR circuit 1636 (YE/BK). GO to  T36.
  14. T14 CHECK FOR LOW RESISTANCE ON CIRCUIT 1635 (OG/LG) AND CIRCUIT 1636 (YE/BK) BETWEEN THE RCM AND THE PASSENGER SAFETY CANOPY MODULE SQUIB 1 
    • Key in OFF position.
    • Disconnect: Passenger Safety Canopy Module Restraint System Diagnostic Tool.
    • For Five Hundred and Montego vehicles,  measure the resistance between passenger safety canopy module C9032 pin 1, circuit 1635 (OG/LG), and passenger safety canopy module C9032 pin 2, circuit 1636 (YE/BK), harness side.
      Fig 19: Checking For Low Resistance On Circuit 1635 (OG/LG) And Circuit 1636 (YE/BK) Between RCM And Passenger Safety Canopy Module Squib 1
      G03953493Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between passenger safety canopy module C9019 pin 1, circuit 1635 (OG/LG), and passenger safety canopy module C9019 pin 2, circuit 1636 (YE/BK), harness side.
      Fig 20: Measuring Resistance Between Connector Terminals
      G03903697Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to T15.
    2. No  : GO to  T34.
  15. T15 CHECK THE RCM FOR LOW RESISTANCE 
    • Disconnect: RCM C310a and C310b.
    • Measure the resistance between RCM C310b pin 5, component side and pin 6, component side.
      Fig 21: Measuring Resistance Between RCM Connector Terminals
      G03946361Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to  T34.
    2. No  : REPAIR circuit 1635 (OG/LG) and circuit 1636 (YE/BK). GO to  T36.
  16. T16 CHECK CIRCUIT 1914 (YE/LG) AND CIRCUIT 1915 (BN/OG) FOR A SHORT TO BATTERY BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE SQUIB 2 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • Repower the system. Do not  prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Key in ON position.
    • Measure the voltage between driver safety canopy module C9018 pin 3, circuit 1914 (YE/LG), harness side and ground; and between driver safety canopy module C9018 pin 4, circuit 1915 (BN/OG), harness side and ground.
      Fig 22: Measuring Voltage Between connector Terminals And Ground
      G03903673Courtesy of FORD MOTOR CO.
    • Are the voltages less than 0.2 volt? 
    1. Yes  : GO to  T34.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1914 (YE/LG) or circuit 1915 (BN/OG). GO to  T36.

  17. T17 CHECK CIRCUIT 1914 (YE/LG) AND CIRCUIT 1915 (BN/OG) FOR A SHORT TO GROUND BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE SQUIB 2 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • Measure the resistance between RCM C310b pin 7, circuit 1914 (YE/LG), harness side and ground; and between RCM C310b pin 8, circuit 1915 (BN/OG), harness side and ground.
      Fig 23: Checking Circuit 1914 (YE/LG) And Circuit 1915 (BN/OG) For Short To Ground Between RCM And Driver Safety Canopy Module Squib 2
      G03989665Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10,000 ohms? 
    1. Yes  : GO to  T34.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1914 (YE/LG) or circuit 1915 (BN/OG). GO to  T36.

  18. T18 CHECK CIRCUIT 1914 (YE/LG) FOR AN OPEN BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE SQUIB 2 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • Measure the resistance between RCM C310b pin 7, circuit 1914 (YE/LG), harness side and driver safety canopy module C9018 pin 3, circuit 1914 (YE/LG), harness side.
      Fig 24: Checking Circuit 1914 (YE/LG) For Open Between RCM And Driver Safety Canopy Module Squib 2
      G03989666Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to T19.
    2. No  : REPAIR circuit 1914 (YE/LG). GO to  T36.
  19. T19 CHECK CIRCUIT 1915 (BN/OG) FOR AN OPEN BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE SQUIB 2 
    • Measure the resistance between RCM C310b pin 8, circuit 1915 (BN/OG), harness side and driver safety canopy module C9018 pin 4, circuit 1915 (BN/OG), harness side.
      Fig 25: Checking Circuit 1915 (BN/OG) For Open Between RCM And Driver Safety Canopy Module Squib 2
      G03989667Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to  T28.
    2. No  : REPAIR circuit 1915 (BN/OG). GO to  T36.
  20. T20 CHECK FOR LOW RESISTANCE ON CIRCUIT 1914 (YE/LG) AND CIRCUIT 1915 (BN/OG) BETWEEN THE DRIVER SAFETY CANOPY MODULE AND THE RCM SQUIB 2 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Restraint System Diagnostic Tool.
    • Measure the resistance between driver safety canopy module C9018 pin 1, circuit 1914 (YE/LG), and driver safety canopy module C9018 pin 2, circuit 1915 (BN/OG), harness side.
      Fig 26: Measuring Resistance Between Connector Terminals
      G03903679Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to T21.
    2. No  : GO to  T34.
  21. T21 CHECK THE RCM FOR LOW RESISTANCE 
    • Disconnect: RCM C310a and C310b.
    • Measure the resistance between RCM C310b pin 7, component side and pin 8, component side.
      Fig 27: Measuring Resistance Between RCM C310B Pin 7, Component Side And Pin 8, Component Side
      G03989669Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to  T34.
    2. No  : REPAIR circuit 1914 (YE/LG) and circuit 1915 (BN/OG). GO to  T36.
  22. T22 CHECK CIRCUIT 1916 (PK/WH) AND CIRCUIT 1917 (YE/LB) FOR A SHORT TO BATTERY BETWEEN THE RCM AND THE PASSENGER SAFETY CANOPY MODULE SQUIB 2 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Passenger Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • Repower the system. Do not  prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Key in ON position.
    • Measure the voltage between passenger safety canopy module C9019 pin 3, circuit 1916 (PK/WH), harness side and ground; and between passenger safety canopy module C9019 pin 4, circuit 1917 (YE/LB), harness side and ground.
      Fig 28: Measuring Voltage Between connector Terminals And Ground
      G03903673Courtesy of FORD MOTOR CO.
    • Are the voltages less than 0.2 volt? 
    1. Yes  : GO to  T34.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1916 (PK/WH) or circuit 1917 (YE/LB). GO to  T36.

  23. T23 CHECK CIRCUIT 1916 (PK/WH) AND CIRCUIT 1917 (YE/LB) FOR A SHORT TO GROUND BETWEEN THE RCM AND THE PASSENGER SAFETY CANOPY MODULE SQUIB 2 
    • Key in OFF position.
    • Disconnect: Passenger Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310b.
    • Measure the resistance between RCM C310b pin 9, circuit 1916 (PK/WH), harness side and ground; and between RCM C310b pin 10, circuit 1917 (YE/LB), harness side and ground.
      Fig 29: Checking Circuit 1916 (PK/WH) And Circuit 1917 (YE/LB) For Short To Ground Between RCM And Passenger Safety Canopy Module Squib 2
      G03989671Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10,000 ohms? 
    1. Yes  : GO to  T34.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1916 (PK/WH) or circuit 1917 (YE/LB). GO to  T36.

  24. T24 CHECK CIRCUIT 1916 (PK/WH) FOR AN OPEN BETWEEN THE RCM AND THE PASSENGER SAFETY CANOPY MODULE SQUIB 2 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Passenger Safety Canopy Module Restraint System Diagnostic Tool.
    • Disconnect: RCM C310a and C310b.
    • Measure the resistance between RCM C310b pin 9, circuit 1916 (PK/WH), harness side and passenger safety canopy module C9019 pin 3, circuit 1916 (PK/WH), harness side.
      Fig 30: Checking Circuit 1916 (PK/WH) For Open Between RCM And Passenger Safety Canopy Module Squib 2
      G03989672Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to T25.
    2. No  : REPAIR circuit 1916 (PK/WH). GO to  T36.
  25. T25 CHECK CIRCUIT 1917 (YE/LB) FOR AN OPEN BETWEEN THE RCM AND THE PASSENGER SAFETY CANOPY MODULE SQUIB 2 
    • Measure the resistance between RCM C310b pin 10, circuit 1917 (YE/LB), harness side and passenger safety canopy module C9019 pin 4, circuit 1917 (YE/LB), harness side.
      Fig 31: Checking Circuit 1917 (YE/LB) For Open Between RCM And Passenger Safety Canopy Module Squib 2
      G03989673Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to  T34.
    2. No  : REPAIR circuit 1917 (YE/LB). GO to  T36.
  26. T26 CHECK FOR LOW RESISTANCE ON CIRCUIT 1916 (PK/WH) AND CIRCUIT 1917 (YE/LB) BETWEEN THE RCM AND PASSENGER SAFETY CANOPY MODULE SQUIB 2 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING . Disconnect: Passenger Safety Canopy Module Restraint System
    • Diagnostic Tool.
    • Measure the resistance between passenger safety canopy module C9019 pin 3, circuit 1916 (PK/WH), and passenger safety canopy module C9019 pin 4, circuit 1917 (YE/LB), harness side.
      Fig 32: Measuring Resistance Between Connector Terminals
      G03903679Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to T27.
    2. No  : GO to  T34.
  27. T27 CHECK THE RCM FOR LOW RESISTANCE 
    • Measure the resistance between RCM C310b pin 9, component side and pin 10, component side.
      Fig 33: Measuring Resistance Between RCM C310B Pin 9, Component Side And Pin 10, Component Side
      G03989675Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to  T34.
    2. No  : REPAIR circuit 1916 (PK/WH) and circuit 1917 (YE/LB). GO to  T36.
  28. T28 CHECK CIRCUIT 1633 (BK/OG)/1652 (WH/LB) AND CIRCUIT 1634 (RD/PK)/1653 (BR/LB) FOR A SHORT TO BATTERY BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE (FIVE HUNDRED AND MONTEGO) 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Bridge Resistor.
    • Disconnect: RCM C310a and C310b.
    • Repower the system. Do not  prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Key in ON position.
    • For Five Hundred and Montego vehicles,  measure the voltage between driver safety canopy module C9016 pin 1, circuit 1652 (WH/LB), harness side and ground; and between driver safety canopy module C9016 pin 2, circuit 1653 (BR/LB), harness side and ground.
      Fig 34: Measuring Voltage Between Driver Safety Canopy Module C9016 Pin 1, Circuit 1652 (WH/LB), Harness Side And Ground
      G03989676Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the voltage between driver safety canopy module C9016 pin 1, circuit 1633 (BK/OG), harness side and ground; and between driver safety canopy module C9016 pin 2, circuit 1634 (RD/PK), harness side and ground.
      Fig 35: Measuring Voltage Between Driver Safety Canopy Module C9016 Pin 1, Circuit 1633 (BK/OG), Harness Side And Ground
      G03989676Courtesy of FORD MOTOR CO.
    • Are the voltages less than 0.2 volt? 
    1. Yes  : GO to  T34.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1633 (BK/OG)/1652 (WH/LB) or circuit 1634 (RD/PK)/1653 (BR/LB). GO to  T36.

  29. T29 CHECK CIRCUIT 1633 (BK/OG)/1652 (WH/LB) AND CIRCUIT 1634 (RD/PK)/1653 (BR/LB) FOR A SHORT TO GROUND BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE (FIVE HUNDRED AND MONTEGO) 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Bridge Resistor.
    • Disconnect: RCM C310a and C310b.
    • For Five Hundred and Montego vehicles,  measure the resistance between driver safety canopy module C9016 pin 1, circuit 1652 (WH/LB), harness side and ground; and between driver safety canopy module C9016 pin 2, circuit 1653 (BR/LB), harness side and ground.
      Fig 36: Measuring Resistance Between Driver Safety Canopy Module C9016 Pin 1, Circuit 1652 (WH/LB), Harness Side And Ground
      G03989678Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between driver safety canopy module C9016 pin 1, circuit 1633 (BK/OG), harness side and ground; and between driver safety canopy module C9016 pin 2, circuit 1634 (RD/PK), harness side and ground.
      Fig 37: Measuring Resistance Between Driver Safety Canopy Module C9016 Pin 1, Circuit 1633 (BK/OG), Harness Side And Ground
      G03989678Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10,000 ohms? 
    1. Yes  : GO to  T34.
    2. No  : Due to the shorting bar feature in the electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit 1633 (BK/OG)/1652 (WH/LB) or circuit 1634 (RD/PK)/1653 (BR/LB). GO to  T36.

  30. T30 CHECK CIRCUIT 1633 (BK/OG)/1652 (WH/LB) FOR AN OPEN BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE (FIVE HUNDRED AND MONTEGO) 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Bridge Resistor.
    • Disconnect: RCM C310a and C310b.
    • For Five Hundred and Montego vehicles,  measure the resistance between RCM C310b pin 3, circuit 1652 (WH/LB), harness side and driver safety canopy module C9016 pin 1, circuit 1652 (WH/LB), harness side.
      Fig 38: Checking Circuit 1633 (BK/OG)/1652 (WH/LB) For Open Between RCM And Driver Safety Canopy Module
      G03989680Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between RCM C310b pin 3, circuit 1633 (BK/OG), harness side and driver safety canopy module C9018 pin 1, circuit 1633 (BK/OG), harness side.
      Fig 39: Measuring Resistance Between RCM C310B Pin 3, Circuit 1633 (BK/OG), Harness Side And Driver Safety Canopy Module C9018 Pin 1
      G03989680Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to T31.
    2. No  : REPAIR circuit 1633 (BK/OG)/1652 (WH/LB). GO to  T36.
  31. T31 CHECK CIRCUIT 1634 (RD/PK)/1653 (BR/LB) FOR AN OPEN BETWEEN THE RCM AND THE DRIVER SAFETY CANOPY MODULE (FIVE HUNDRED AND MONTEGO) 
    • For Five Hundred and Montego vehicles,  measure the resistance between RCM C310b pin 4, circuit 1653 (BR/LB), harness side and driver safety canopy module C9016 pin 2, circuit 1653 (BR/LB), harness side.
      Fig 40: Checking Circuit 1634 (RD/PK)/1653 (BR/LB) For Open Between RCM And Driver Safety Canopy Module
      G03989682Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between RCM C310b pin 4, circuit 1634 (RD/PK), harness side and driver safety canopy module C9016 pin 2, circuit 1634 (RD/PK), harness side.
      Fig 41: Measuring Resistance Between RCM C310B Pin 4, Circuit 1634 (RD/PK), Harness Side And Driver Safety Canopy Module C9016 Pin 2
      G03989682Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to  T34.
    2. No  : REPAIR circuit 1634 (RD/PK)/1653 (BR/LB). GO to
  32. T32 CHECK FOR LOW RESISTANCE ON CIRCUIT 1633 (BK/OG)/1652 (WH/LB) AND CIRCUIT 1634 (RD/PK)/1653 (BR/LB) BETWEEN THE DRIVER SAFETY CANOPY MODULE AND THE RCM (FIVE HUNDRED AND MONTEGO) 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Canopy Module Bridge Resistor.
    • For Five Hundred and Montego vehicles,  measure the resistance between driver safety canopy module C9016 pin 1, circuit 1652 (WH/LB), and driver safety canopy module C9016 pin 2, circuit 1653 (BR/LB), harness side.
      Fig 42: Measuring Resistance Between Driver Safety Canopy Module C9016 Pin 1, Circuit 1652 (WH/LB), And Driver Safety Canopy Module C9016 Pin 2
      G03989684Courtesy of FORD MOTOR CO.
    • For Freestyle vehicles,  measure the resistance between driver safety canopy module C9016 pin 1, circuit 1633 (BK/OG), and driver safety canopy module C9016 pin 2, circuit 1634 (RD/PK), harness side.
      Fig 43: Measuring Resistance Between Driver Safety Canopy Module C9016 Pin 1, Circuit 1633 (BK/OG), And Driver Safety Canopy Module C9016 Pin 2
      G03989684Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to T33.
    2. No  : GO to  T34.
  33. T33 CHECK THE RCM FOR LOW RESISTANCE 
    • Disconnect: RCM C310a and C310b.
    • Measure the resistance between RCM C310b pin 3, component side and pin 4, component side.
      Fig 44: Measuring Resistance Between RCM Connector Terminals
      G04011460Courtesy of FORD MOTOR CO.
    • Is the resistance less than 10,000 ohms? 
    1. Yes  : GO to T34.
    2. No  : REPAIR circuit 1633 (BK/OG)/1652 (WH/LB) and circuit 1634 (RD/PK)/1652 (WH/LB). GO to  T36.
  34. T34 CONFIRM THE RCM FAULT 
    NOTE: Make sure all restraint system diagnostic tools, sensor electrical connectors and the RCM electrical connectors are connected before carrying out the on-demand self test. If not, erroneous DTCs will be recorded.
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Connect: Restraint System Diagnostic Tools (vehicles with safety canopies).
    • Connect: Safety Canopy Bridge Resistor (vehicles without safety canopies).
    • Connect: RCM C310a and C310b.
    • Repower the system. Do not  prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
    • Enter the following diagnostic mode on the scan tool: Flag DTC B2294/Record All Flagged Faults.
    • Was DTC B2294 retrieved during the on-demand self test? 
    1. Yes  : If a "?  " was flagged by the diagnostic tool, CARRY OUT the entire pinpoint test.

      INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE (RCM) . GO to  T36.

    2. No  : Fault corrected. GO to  T36.
  35. T35 CHECK FOR AN INTERMITTENT FAULT 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • If the flagged fault was reported for the driver safety canopy module:
      • Vehicles with safety canopy modules 

        Disconnect the driver safety canopy module C9018 (Freestyle) or C9031 (Five Hundred, Montego). Refer to SAFETY CANOPY MODULE - FREESTYLE  or SAFETY CANOPY MODULE - FIVE HUNDRED, MONTEGO .

      • Vehicles with safety canopy modules 

        Connect restraint system diagnostic tool 418-F403 (Freestyle) or 418-F395 (Five Hundred, Montego) to the driver safety canopy module C9018 (Freestyle) or C9031 (Five Hundred, Montego).

      • Vehicles without safety canopy modules 

        Disconnect driver safety canopy module bridge resistor.

      • Vehicles without safety canopy modules 

        Install a known good driver safety canopy module bridge resistor.

    • If the flagged fault was reported for the passenger safety canopy module:
    • Repower the system. Do not  prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
    • Enter the following diagnostic mode on the scan tool: Flag DTC B2294/Record All Flagged Faults.
    • Was DTC B2294 retrieved during on-demand self test? 
    1. Yes : Vehicles with safety canopy modules 

      This is a hard fault. The fault condition is now present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test.

      CHECK for causes of the intermittent fault at or near the affected safety canopy module connector. REPAIR any intermittent concerns found.

      If an intermittent concern was  found and repaired, GO to T36.

      If an intermittent concern was not  found and repaired, USE the flagged faults recorded and GO to the appropriate PINPOINT TEST .

      If a flagged fault of "?  " was recorded, multiple faults exist and the entire pinpoint test must be carried out.

      Using the flagged faults recorded, GO to the appropriate PINPOINT TEST .

      For driver safety canopy module squib 1 (DFCURTN) with a short to battery (STB) fault, GO to  T4.

      For driver safety canopy module squib 1 (DFCURTN) with a short to ground (STG) fault, GO to  T5.

      For driver safety canopy module squib 1 (DFCURTN) with an open circuit (O_CIR) fault, GO to  T6.

      For driver safety canopy module squib 1 (DFCURTN) with a low resistance (LOWRES) fault, GO to  T8.

      For passenger safety canopy module squib 1 (PFCURTN) with a short to battery (STB) fault, GO to  T10.

      For passenger safety canopy module squib 1 (PFCURTN) with a short to ground (STG) fault, GO to  T11.

      For passenger safety canopy module squib 1 (PFCURTN) with an open circuit (O_CIR) fault, GO to  T12.

      For passenger safety canopy module squib 1 (PFCURTN) with a low resistance (LOWRES) fault, GO to  T14.

      For driver safety canopy module squib 2 (DRCURTN) with a short to battery (STB) fault, GO to  T16.

      For driver safety canopy module squib 2 (DRCURTN) with a short to ground (STG) fault, GO to  T17.

      For driver safety canopy module squib 2 (DRCURTN) with an open circuit (O_CIR) fault, GO to  T18.

      For driver safety canopy module squib 2 (DRCURTN) with a low resistance (LOWRES) fault, GO to  T18.

      For passenger safety canopy module squib 2 (PRCURTN) with a short to battery (STB) fault, GO to  T22.

      For passenger safety canopy module squib 2 (PRCURTN) with a short to ground (STG) fault, GO to  T23.

      For passenger safety canopy module squib 2 (PRCURTN) with an open circuit (O_CIR) fault, GO to  T24.

      For passenger safety canopy module squib 2 (PRCURTN) with a low resistance (LOWRES) fault, GO to  T26.

      Vehicles without safety canopy modules 

      This is a hard fault. The fault condition is now present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test.

      If a flagged fault of "?  " was recorded, multiple faults exist and the entire pinpoint test must be carried out.

      For driver safety canopy module (DFCURTN) with a short to battery (STB) fault, GO to  T28.

      For driver safety canopy module (DFCURTN) with a short to ground (STG) fault, GO to  T29.

      For driver safety canopy module (DFCURTN) with an open circuit (O_CIR) fault, GO to  T30.

      For driver safety canopy module (DFCURTN) with a low resistance (LOWRES) fault, GO to  T32.

    2. No  : CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to T36.
  36. T36 CHECK FOR ADDITIONAL DTCs 
    • Refer to the continuous DTCs recorded during Step  T1.
    • Were any continuous DTCs retrieved during Step   T1 ? 
    1. Yes  : Do not clear any DTCs until all DTCs have been resolved. GO to the RESTRAINTS CONTROL MODULE (RCM) DIAGNOSTIC TROUBLE CODE (DTC) TABLE  for pinpoint test direction.
    2. No  : RECONNECT the system. If previously directed to deactivate the system, REACTIVATE the system. REFER to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEACTIVATION AND REACTIVATION . REPOWER the system. REFER to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING . PROVE OUT the system. CLEAR all DTCs.
scientia non olet · About LEMON Manuals