LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1110 (Supplemental Inflatable Restraint System) >> Diagnosis And Testing >> Pinpoint Tests - Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Test O: LFC 18/DTC B1884 - PAD Warning Lamp Circuit Failure >> Testing

Pinpoint Test O: LFC 18/DTC B1884 - PAD Warning Lamp Circuit Failure: Testing

WARNING: This page is about a different car, the 2005 Mercury Montego, 2005 Ford Freestyle, and 2005 Ford Five Hundred. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough Inspection and Verification before proceeding with the pinpoint test.
  1. O1 CHECK FOR CONTINUOUS OR ON-DEMAND DTCs 
    WARNING: Restraint system diagnostic tools are for service only. Tools must be removed prior to operating the vehicle over the road. Failure to remove restraint system diagnostic tools could result in injury and possible violation of vehicle safety standards.
    WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow these instructions may result in the inadvertent deployment of the safety canopy and risk of personal injury.
    WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.
    WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe a pretensioner electrical connector. Doing so could result in pretensioner or air bag deployment and could result in personal injury.
    WARNING: Never probe the electrical connector on a safety canopy module. Doing so can result in safety canopy deployment.
    NOTE: If a seat equipped with a supplemental restraint system (SRS) component is being serviced, the SRS must be depowered.
    NOTE: After diagnosing or repairing an SRS, the restraint system diagnostic tools must be removed before operating the vehicle over the road. 
    NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
    • Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
    • Enter the following diagnostic mode on the scan tool: Retrieve/Record Continuous DTCs.
    • Was DTC B1884 retrieved during the on-demand self test? 
    1. Yes  : If the PAD indicator does illuminate, GO to O2.

      If the PAD indicator does not illuminate, GO to  O4.

    2. No  : This is an intermittent fault. The fault condition is not present at this time. GO to  O8.
  2. O2 CHECK CIRCUIT 1632 (TN/LB) FOR SHORT TO GROUND 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RCM C310a and C310b.
    • Disconnect: PAD Indicator C2286.
    • Measure the resistance between the PAD indicator C2286 pin 1, circuit 1632 (TN/LB), harness side and ground.
      • Fig 1: Measuring Resistance Between Pad Indicator C2286 Pin 1, Circuit 1632 (TN/LB), Harness Side And Ground
      G03989580Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10,000 ohms? 
    1. Yes  : GO to  O7.
    2. No  : GO to O3.
  3. O3 CHECK RCM 
    • Measure the resistance between RCM C310a pin 24, circuit 1632 (TN/LB), component side and ground.
      Fig 2: Measuring Resistance Between RCM C310a Pin 24, Circuit 1632 (TN/LB), Component Side And Ground
      G03989581Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10,000 ohms? 
    1. Yes  : REPAIR circuit 1632 (TN/LB). GO to  O9.
    2. No  : GO to  O7.
  4. O4 CHECK CIRCUIT 1632 (TN/LB) FOR OPEN 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RCM C310a and C310b.
    • Disconnect: PAD Indicator C2286.
    • Measure the resistance between the PAD indicator C2286 pin 1, circuit 1632 (TN/LB), harness side and the RCM C310a pin 24, circuit 1632 (TN/LB), harness side.
      Fig 3: Measuring Resistance Between Pad Indicator C2286 Pin 1, Circuit 1632 (TN/LB), Harness Side
      G03989582Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    1. Yes  : GO to O5.
    2. No  : REPAIR circuit 1632 (TN/LB). GO to  O9.
  5. O5 CHECK CIRCUIT 1809 (WH) FOR OPEN 
    • Repower the system. Do not prove out the system at this time.

      Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .

    • Key in ON position.
    • Measure the voltage between the PAD indicator C2286 pin 3, circuit 1809 (WH), harness side and ground.
      Fig 4: Measuring Voltage Between Pad Indicator C2286 Pin 3, Circuit 1809 (WH), Harness Side And Ground
      G03989583Courtesy of FORD MOTOR CO.
    • Is the voltage greater than 10 volts? 
    1. Yes  : GO to O6.
    2. No  : REPAIR circuit 1809 (WH). GO to  O9.
  6. O6 CHECK PAD INDICATOR LAMP 
    • Key in OFF position.
    • Deactivate the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEACTIVATION AND REACTIVATION .
    • Connect: PAD Indicator C2286.
    • Key in ON position.
    • Connect a fused jumper wire between RCM C310a pin 24, circuit 1632 (TN/LB), harness side and ground.
      Fig 5: Connecting Fused Jumper Wire Between RCM C310a Pin 24, Circuit 1632 (TN/LB), Harness Side And Ground
      G03989584Courtesy of FORD MOTOR CO.
    • Does the PAD indicator illuminate? 
    1. Yes  : GO to O7.
    2. No  : INSTALL a new PAD indicator. REFER to PASSENGER AIR BAG DEACTIVATION (PAD) INDICATOR - FREESTYLE  or PASSENGER AIR BAG DEACTIVATION (PAD) INDICATOR - FIVE HUNDRED, MONTEGO . GO to  O9.
  7. O7 CONFIRM THE RCM FAULT 
    NOTE: Make sure all restraint system diagnostic tools, sensor electrical connectors, and the RCM electrical connector are connected before carrying out the on-demand self test. If not, erroneous DTCs will be recorded.
    1. Yes  : INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE (RCM) . GO to  O9.
    2. No  : CHECK for causes of intermittent open or short to ground on circuit 1632 (TN/LB). ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to  O9.
  8. O8 CHECK FOR AN INTERMITTENT FAULT 
    • Key in OFF position.
    • Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
    • Was DTC B1884 retrieved during the on-demand self test? 
    1. Yes  : GO to  O2.
    2. No  : CHECK for causes of intermittent open or short to ground on circuit 1632 (TN/LB). ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to O9.
  9. O9 CHECK FOR ADDITIONAL DTCs 
    • Refer to the continuous DTCs recorded during Step  O1.
    • Were any continuous DTCs retrieved during Step   O1 ? 
    1. Yes  : Do not clear any DTCs until all DTCs have been resolved. GO to the RESTRAINTS CONTROL MODULE (RCM) DIAGNOSTIC TROUBLE CODE (DTC) PRIORITY TABLE  for pinpoint test direction.
    2. No  : RECONNECT the system. If previously directed to deactivate the system, REACTIVATE the system. REFER to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEACTIVATION AND REACTIVATION . REPOWER the system. REFER to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING . PROVE OUT the system. CLEAR all DTCs.
scientia non olet · About LEMON Manuals