LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 106 (Supplemental Inflatable Restraint System - F150 Pickup) >> Diagnostic Tests >> Test U: Passenger Air Bag Circuit Resistance High (DTC B1933) >> Possible Causes

Possible Causes

WARNING: This page is about a different car, the 2002 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.

Passenger-side air bag high resistance could be caused by poor connection or corrosion in passenger-side air bag module circuits, open circuit or high resistance in wiring harness, open or high resistance in passenger-side air bag module or faulty RCM.

  1. Check for hard or intermittent DTC

    Turn ignition switch to OFF position. Connect scan tool to Data Link Connector (DLC). See USING SCAN TOOL  under DIAGNOSTICS. Turn ignition switch to RUN position. Retrieve and record any continuous DTCs. See RETRIEVING FAULT CODES  under DIAGNOSTICS. Perform on-demand self-test. See ON-DEMAND SELF-TEST  under DIAGNOSTICS. If DTC B1933 was retrieved during on-demand self-test, fault is hard. Go to next step. If DTC B1933 was not retrieved, fault is intermittent. Go to step  4 .

  2. Check passenger-side air bag module

    Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM  under DISABLING & ACTIVATING AIR BAG SYSTEM. Turn ignition switch to RUN position. Perform on-demand self-test. See ON-DEMAND SELF-TEST  under DIAGNOSTICS. If DTC B1933 is retrieved, go to next step. If DTC B1933 is not retrieved, replace passenger-side air bag module. See PASSENGER-SIDE AIR BAG MODULE  under REMOVAL & INSTALLATION. Go to step  5 .
    NOTE: By disconnecting RCM harness connector, circuits No. 607 (Light Blue/Orange wire) and No. 616 (Pink/Black wire) are shorted together by shorting bar. Do not remove shorting bar.

  3. Check passenger-side air bag circuit

    Turn ignition switch to OFF position. Access RCM and disconnect harness connector. See RESTRAINTS CONTROL MODULE (RCM)  under REMOVAL & INSTALLATION. Disconnect passenger-side air bag simulator from harness connector. Zero ohmmeter. Measure resistance between Light Blue/Orange wire (circuit No. 607) and Pink/Black wire (circuit No. 616) on harness side of passenger-side air bag module harness connector. If resistance is more than one ohm, repair Light Blue/Orange or Pink/Black wires as necessary. See WIRING DIAGRAMS  . Go to step  5 . If resistance is less than one ohm, replace RCM. Go to step  5 .

  4. Check for intermittent fault

    Refer to continuous DTCs recorded in step  1 . If DTC retrieved in step  1 was an intermittent fault, check for cause of intermittent high resistance in Light Blue/Orange wire (circuit No. 607) and Pink/Black wire (circuit No. 616). See WIRING DIAGRAMS  . Attempt to recreate fault by flexing wire harness and cycling ignition switch frequently. Repair any intermittent problems found. Go to next step. If DTC retrieved in step  1 was not an intermittent fault. Go to next step.

  5. Check for additional DTCs

    Refer to continuous DTCs recorded in step  1 . If any continuous DTCs were retrieved, go to diagnostic trouble code identification table for direction to appropriate test. See DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION  table. DO NOT clear any DTCs until all DTCs have been resolved. If no continuous DTCs were retrieved, reconnect air bag system. Activate air bag system. See ACTIVATING SYSTEM  under DISABLING & ACTIVATING AIR BAG SYSTEM. Clear all DTCs. See CLEARING FAULT CODES  under DIAGNOSTICS.
scientia non olet · About LEMON Manuals