LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1015 (Supplemental Inflatable Restraint System -- F150 Pickup) >> Diagnosis And Testing >> Pinpoint Tests - Air Bag and Safety Belt Pretensioner Supplemental Restraint System SRS >> Pinpoint Test W: LFC 49/DTC C1981 - Driver Seat Track Position Sensor Circuit Fault >> Pinpoint Test W: LFC 49/DTC C1981 - Seat Track Position Sensor Circuit Fault

Pinpoint Test W: LFC 49/DTC C1981 - Seat Track Position Sensor Circuit Fault

WARNING: This page is about a different car, the 2005 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough Inspection and Verification before proceeding with the pinpoint test.
  1. W1 CHECK FOR A HARD OR INTERMITTENT DTC 
    WARNING: Restraint system diagnostic tools are for service only. Tools must be removed prior to operating the vehicle over the road. Failure to remove restraint system diagnostic tools could result in injury and possible violation of vehicle safety standards.
    WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.
    WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe a pretensioner electrical connector. Doing so could result in pretensioner or air bag deployment and could result in personal injury.
    NOTE: After diagnosing or repairing an SRS, the restraint system diagnostic tools must be removed before operating the vehicle over the road.
    NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
    • Enter the following diagnostic mode on the diagnostic tool: On-Demand Self Test.
    • Enter the following diagnostic mode on the diagnostic tool: Retrieve/Record Continuous DTCs.
    • Was DTC C1981 retrieved during the on-demand self test? 
    • Yes  : This is a hard fault. The fault condition is still present. This fault cannot be cleared until it is corrected and DTC is no longer retrieved during the on-demand self test. GO to  W2.
    • No  : This is an intermittent fault. The fault condition is not present at this time. GO to  W7
  2. W2 CHECK CIRCUIT 1520 (LG) FOR A SHORT TO VOLTAGE 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM SRS DEPOWERING AND REPOWERING .
    • Disconnect: Driver Safety Belt Buckle Pretensioner C3201.
    • Connect: Restraint System Diagnostic Tool 418-F395 to Driver Safety Belt Buckle Pretensioner C3201.
    • Disconnect: RCM C310a and C310b.
    • Disconnect: Driver Seat Track Position Sensor C356.
    • Repower the system. Do not  prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM SRS DEPOWERING AND REPOWERING .
    • Key in ON position.
    • Measure the voltage between seat track position sensor C356 pin 2, circuit 1520 (LG), harness side and ground.
      Fig 1: Measuring Voltage Between Seat Track Position Sensor C356 Pin 2, Circuit 1520 (LG), Harness Side And Ground
      G03903770Courtesy of FORD MOTOR CO.
    • Is the voltage less than 0.2 volt? 
    • Yes  : GO to  W3.
    • No  : REPAIR circuit 1520 (LG). GO to  W8.
  3. W3 CHECK CIRCUIT 1520 (LG) FOR AN OPEN 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM SRS DEPOWERING AND REPOWERING .
    • Measure the resistance between RCM C310b pin 23, circuit 1520 (LG), harness side and driver seat C356 pin 2, circuit 1520 (LG), harness side.
      Fig 2: Checking Circuit 1520 (LG) For An Open
      G03966676Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    • Yes  : GO to  W4.
    • No  : REPAIR circuit 1520 (LG). GO to  W8.
  4. W4 CHECK CIRCUIT 1203 (BK/LB) FOR AN OPEN 
    • Measure the resistance between seat track position sensor C356 pin 1, circuit 1203 (BK/LB), harness side and ground.
      Fig 3: Measuring Resistance Between Seat Track Position Sensor C356 Pin 1, Circuit 1203 (BK/LB), Harness Side And Ground
      G03966677Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 
    • Yes  : GO to  W5.
    • No  : REPAIR circuit 1203 (BK/LB). GO to  W8.
  5. W5 CHECK THE SEAT TRACK POSITION SENSOR 
    • Yes  : GO to  W6.
    • No  : Fault corrected. GO to  W8.
  6. W6 CONFIRM THE RCM FAULT 
    NOTE: Make sure all restraint system diagnostic tools, sensor electrical connectors and the RCM electrical connector are connected before carrying out the on-demand self test. If not, erroneous DTCs will be recorded.
    • Yes  : INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE RCM . GO to  W8.
    • No  : CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to  W8.
  7. W7 CHECK FOR AN INTERMITTENT FAULT 
    • Key in OFF position.
    • Enter the following diagnostic mode on the diagnostic tool: On-Demand Self Test.
    • Was DTC C1981 retrieved during the on-demand self test? 
    • Yes  : This is a hard fault. The fault condition is now present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test.

      GO to  W2.

    • No  : CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to W8.
  8. W8 CHECK FOR ADDITIONAL DTCs 
    • Refer to the continuous DTCs recorded during Step  W1.
    • Were any continuous DTCs retrieved during Step   W1 ? 
scientia non olet · About LEMON Manuals