LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> Engine Performance >> Testing & Diagnosis >> Engine Controls - Self-Diagnostics - EEC-V - CNG, Flex-Fuel & Gasoline >> System Tests (Evaporative Emissions) >> Test D: Hiss When Opening Fuel Cap >> All Other Models

All Other Models

  1. Testing EVAP Canister & Canister Vent Solenoid Flow -  Connect Evaporative Emissions System Leak Tester (134-00056) or equivalent to test port. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, EVAP canister and vent solenoid are not blocked, go to step  9. On Crown Victoria, Grand Marquis and Town Car, if pressure does not drop immediately, go to next step. On all other models, if pressure does not drop immediately, go to step  3.

  2. Testing Canister Vent Solenoid Remote Vent Hose Assembly For Blockage

    Disconnect canister vent solenoid remote vent hose from in-line connector. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace canister vent solenoid remote vent hose. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If pressure does not drop immediately, go to next step.

  3. Testing Canister Vent Solenoid Hose Assembly For Blockage

    Disconnect canister vent solenoid hose assembly. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace canister vent solenoid hose assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If pressure does not drop immediately, go to next step.

  4. Testing Canister Vent Solenoid For Blockage

    Remove canister vent solenoid. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace canister vent solenoid. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to next step.

  5. Testing EVAP Canister

    Disconnect EVAP canister tube at canister that runs from EVAP canister to fuel tank. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace EVAP canister. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to next step.

  6. Testing EVAP Canister Tube

    Disconnect EVAP canister tube at fuel vapor valve tube assembly that runs from EVAP canister to fuel tank. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace EVAP canister tube. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to next step.

  7. Testing EVAP Canister Purge Outlet Tube

    Disconnect EVAP canister purge outlet tube at fuel vapor valve tube assembly that runs from EVAP purge valve to fuel tank. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, go to step  9. If pressure does not drop immediately, go to next step.

  8. Testing Evaporative Emissions Test Port

    Disconnect evaporative emissions test port from EVAP canister purge outlet tube. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace EVAP canister purge outlet tube. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, replace evaporative emissions test port. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS.

  9. Testing Fuel Vapor Valve Tube Assembly

    Disconnect EVAP canister purge outlet tube at fuel vapor valve tube assembly. Connect EVAP Tester to fuel filler tube. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, reconnect all components. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, replace fuel vapor valve tube assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS.
scientia non olet · About LEMON Manuals