LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis (Single Page) >> Engine Performance >> Testing & Diagnosis >> Engine Controls - Self-Diagnostics - EEC-V - CNG, Flex-Fuel & Gasoline >> System Tests (Evaporative Emissions) >> Test D: Hiss When Opening Fuel Cap >> Mustang

Test D: Hiss When Opening Fuel Cap: Mustang

  1. Testing Fuel Tank Pressure Sensor -  Connect Evaporative Emissions System Leak Tester (134-00056) or equivalent to fuel filler pipe. Turn ignition switch to ON position. Using scan tool, close canister vent solenoid. Select OUTPUT TEST MODE, FTP and VPID. Select ALL OFF mode. Press START button on scan tool to close canister vent solenoid. Pressurize system to 3.48 kPa (14 In. H2O). If FTP V PID is 4.22-4.90 volts, go to next step. If FTP V PID is not 4.22-4.90 volts, go to step  3.

  2. Testing Venting Portion Of EVAP System For Blockage

    Using scan tool, open canister vent solenoid by selecting STOP button. If pressure drops immediately, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to step  7.

  3. Testing Fuel Tank Pressure Sensor Operation

    Move EVAP Tester to evaporative emission test port. Turn ignition switch to ON position. Using scan tool, close canister vent solenoid. Select OUTPUT TEST MODE, FTP and VPID. Select ALL OFF mode. Press START button on scan tool to close canister vent solenoid. Pressurize system to 3.48 kPa (14 In. H2O). If FTP V PID is 4.22-4.90 volts, go to next step. If FTP V PID is not 4.22-4.90 volts, go to TEST HX  under SYSTEM TESTS.

  4. Testing For Location Of Blockage

    Using scan tool, open canister vent solenoid by selecting STOP button. If pressure drops immediately, go to next step. If pressure does not drop immediately, go to step  7.

  5. Testing Fuel Vapor Control Valve Tube For Pinch Or Blockage

    Lower fuel tank about 3/4" (19 mm). Connect EVAP Tester to fuel filler pipe. Turn ignition switch to ON position. Using scan tool, close canister vent solenoid. Select OUTPUT TEST MODE, FTP and VPID. Select ALL OFF mode. Press START button on scan tool to close canister vent solenoid. Pressurize system to 3.48 kPa (14 In. H2O). If FTP V PID is 4.22-4.90 volts, replace fuel vapor control tube assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If FTP V PID is not 4.22-4.90 volts, go to next step.

  6. Testing Fuel Filler Tube Assembly

    Disconnect tank vapor recirculation hose at fuel filler pipe and plug both openings. Pressurize system to 3.48 kPa (14 In. H2O). Remove plug from tank vapor recirculation hose. If pressure drops immediately, replace fuel vapor control valve tube assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, replace fuel filler pipe assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS.

  7. Testing Fresh Air Vent Hose

    Disconnect fresh air vent hose from inside trunk. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace fresh air vent hose. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to next step.

  8. Testing Fresh Air Vent Hose At Fuel Filler Pipe

    Disconnect fresh air vent hose at fuel filler pipe. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace fuel filler pipe. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to next step.

  9. Testing Tank Vapor Valve Assembly

    Disconnect tank vapor valve assembly fresh air tube from canister vent solenoid vent hose. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace tank vapor valve assembly fresh air tube. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to next step.

  10. Testing Canister Vent Solenoid Hose Assembly For Blockage

    Disconnect canister vent solenoid hose assembly. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace canister vent solenoid hose assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to next step.

  11. Testing Canister Vent Solenoid For Blockage

    Remove canister vent solenoid. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace canister vent solenoid. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to next step.

  12. Testing EVAP Canister

    Disconnect EVAP canister inlet elbow tube. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace EVAP canister. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, go to next step.

  13. Testing EVAP Canister Inlet Elbow Tube

    Disconnect fuel vapor valve tube assembly from EVAP canister inlet elbow tube. Pressurize system to 3.48 kPa (14 In. H2O). If pressure drops immediately, replace EVAP canister inlet elbow tube. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS. If pressure does not drop immediately, replace fuel vapor valve tube assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform EVAPORATIVE EMISSIONS REPAIR VERIFICATION DRIVE CYCLE. See DRIVE CYCLE PROCEDURES  under ADDITIONAL SYSTEM FUNCTIONS.
scientia non olet · About LEMON Manuals