LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.0 3, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 898 (Engine - 6.0L Diesel -- F250-F550 Super Duty) >> Specifications >> Torque Specifications

Torque Specifications

WARNING: This page is about a different car, the 2005 Ford Pickup, 2005 Ford F550 Super Duty, 2005 Ford F450 Super Duty, and 2005 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Description Nm lb-ft lb-in
Air inlet duct clamp 5 - 44
Turbocharger exhaust adapter V-clamp 12 9 -
Exhaust tube-to-exhaust manifold flange bolts (left side)(1) 27 20 -
Exhaust tube-to-exhaust manifold flange bolts (right side)(1) 27 20 -
Turbocharger flange-to-exhaust/EGR tube bolts (right side)(1) 27 20 -
Turbocharger mounting bolts 31 23 -
Turbocharger pedestal bolts 31 23 -
Turbocharger oil supply tube bolts 24 18 -
Exhaust manifold flange bolts (1) 38 28 -
Intake manifold flange bolts 11 8 -
Intake manifold heat shield 11 8 -
EGR valve mounting bolts 13 10 -
EGR clamp, V-band 6 - 53
EGR cooler bolts, (M6 x 16) 13 10 -
EGR cooler stud bolts (M6 x 55 x 20) 13 10 -
Crankcase breather screws 7 - 62
Cylinder head bolt sequence and torque (2) - - -
Fuel injector hold-down bolt 33 24 -
Rocker arm fulcrum plate 31 23 -
Oil rail assembly (2) - - -
Valve cover bolts and studs 9 - 80
Oil drain pan plug 25 18 -
Front cover module bolts 24 18 -
Thermostat housing retaining bolts 23 17 -
Coolant pump mounting bolts 23 17 -
Vibration damper mounting bolts (2) - - -
Oil pump housing retaining bolts 8 - 71
Connecting rod bearing bolts (2) - - -
Lower crankcase main bearing cap bolts (2) - - -
Lower crankcase outer bolts (M8 x 30) 31 23 -
Oil pickup tube flange bolts 13 10 -
Piston cooling jet mounting bolt (3) 13 10 -
Cam follower mounting bolt 13 10 -
Camshaft thrust plate-mounting bolts 31 23 -
Coolant heater 41 30 -
Oil cooler mounting bolts (6 mm) 10 - 89
Oil cooler mounting bolts (8 mm) 22 16 -
EGR cooler coolant supply port cover (M6) 10 - 89
Oil filter housing bolts (Torx) 15 11 -
Oil filter return tube bolt, new base 5 - 44
Oil filter return tube bolt, reinstallation 3 - 27
Crankshaft position (CKP) sensor 13 10 -
Camshaft position (CMP) sensor 13 10 -
Injection control pressure (ICP) sensor 12 9 -
Injection pressure regulator (IPR) valve 50 37 -
Intake air temperature (IAT2) sensor 17 13 -
Exhaust backpressure tube assembly 30 22 -
Exhaust backpressure (EBP) sensor 12 9 -
Exhaust backpressure (EBP) sensor bracket 12 9 -
Lower oil pan bolt 13 10 -
Upper oil pan bolts 13 10 -
Engine coolant temperature (ECT) sensor 12 9 -
Glow plug 19 14 -
Glow plug module 8 - 71
High pressure oil pump cover bolts 11 8 -
High pressure oil pump mounting bolts 31 23 -
High pressure oil pump discharge tube mounting bolts 11 8 -
Rear heat shield (M6 x 1.0 x 1.2) 11 8 -
Rear heat shield (M10 x 1.5 x 16) 49 36 -
Banjo fitting bolt 38 28 -
Fuel filter plug assembly (back of head) 27 20 -
Flywheel/flexplate mounting bolts 94 69 -
Fuel supply tube at secondary fuel filter 43 32 -
Banjo fitting at secondary fuel filter 35 26 -
Right and left head supply tubes at filter 26 19 -
Front, lifting eye (M10 x 30) 41 30 -
Crankcase-to-Head Tube (Late Build) 82 60 -
Rear, lifting eye (M10 x 35) 41 30 -
Automatic transmission tube nut 8 - 71
Engine ground strap bolt 10 - 89
Starter positive cable nut 12 9 -
Starter control wire nut 6 - 53
Torque converter nut 35 26 -
Motor mount nuts 103 76 -
Turbocharger down pipe bolts 40 30 -
Transmission-to-engine bolts 47 35 -
Transmission tubes mounting bracket bolts 10 - 89
Transmission cooler bolts 8 - 71
Power steering cooler bolts 11 8 -
Battery crossover cable nut 12 9 -
Power steering pump bolt 25 18 -
Battery ground cable-to-engine block bolts 47 35 -
Air conditioning compressor bolts 25 18 -
A/C manifold bolt 21 15 -
Coolant pump mounting bolt 23 17 -
Coolant pump pulley bolts 31 23 -
Cooling fan stator bolts 40 30 -
Fan clutch hub-to-coolant pump 133 98 -
Belt idler pulley bolts 47 35 -
Belt tensioner bolts 25 18 -
Crankshaft pulley bolts (dual alternators) 47 35 -
Alternator mounting bracket bolts (dual alternators) 47 35 -
Starter mounting bolts 25 18 -
Solenoid wire nut 6 - 53
Battery cable nut 12 9 -
Cylinder block drain plug (4) 20 15 -
Charge-air-cooler duct clamps (metal duct) 12 9 -
Charge-air-cooler duct clamps (blow molded duct) 12 9 -
(1) Apply High Temperature Nickel Anti-Seize Lubricant (XL-2) to the threads prior to assembly.
(2) Refer to the procedure in this article.
(3) Apply High Strength Threadlocker to bolt threads prior to assembly.
(4) Apply clean engine oil to the O-ring seal before installing.