LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.0 3, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 729 (Engine - 6.0L Diesel - F250-F550 Super Duty) >> Specifications >> Torque Specifications

Torque Specifications

WARNING: This page is about a different car, the 2004 Ford Pickup, 2004 Ford F550 Super Duty, 2004 Ford F450 Super Duty, 2004 Ford Excursion, and 2004 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Description N.m lb-ft lb-in
Air inlet duct clamp 5 - 44
Turbocharger exhaust adapter V-clamp 12 9 -
Exhaust tube to exhaust manifold flange bolts (left side)(1) 27 20 -
Exhaust tube to exhaust manifold flange bolts (right side)(1) 27 20 -
Turbocharger flange to exhaust/EGR tube bolts (right side)(1) 27 20 -
Turbocharger mounting bolts 38 28 -
Turbocharger pedestal bolts 31 23 -
Turbocharger oil supply tube bolts 24 18 -
Exhaust manifold flange bolts(1) 38 28 -
Intake manifold flange bolts 11 8 -
Intake manifold heat shield 11 8 -
EGR valve mounting bolts 13 10 -
EGR clamp, V-band 6 - 53
EGR cooler bolts, (M8 x 16) 31 23 -
EGR cooler stud bolts (M6 x 55 x 20) 13 10 -
Crankcase breather nuts 7 - 62
Cylinder head bolt sequence and torque(2) - - -
Fuel injector hold-down bolt 33 24 -
Rocker arm fulcrum plate 31 23 -
Glow plugs 19 14 -
ICP sensor 12 9 -
Oil rail assembly(2) - - -
High pressure tube (case to head) - early build vehicles 45 33 -
Oil rail check valve 34 25 -
Oil rail vent plugs 11 8 -
Valve cover bolts and studs 8 - 71
Oil drain pan plug 44 32 -
Front cover module bolts 24 18 -
Thermostat housing retaining bolts 23 17 -
Coolant pump mounting bolts 23 17 -
Vibration damper mounting bolts(2) - - -
Oil pump housing retaining bolts 8 - 71
Connecting rod bearing bolts(2) - - -
Lower crankcase main bearing cap bolts(2) - - -
Lower crankcase outer bolts (M8 x 30) 24 18 -
Oil pickup tube flange bolts 13 10 -
Piston cooling jet mounting bolt(3) 13 10 -
Cam follower mounting bolt 13 10 -
Camshaft thrust plate-mounting bolts 31 23 -
Coolant heater 41 30 -
Oil cooler mounting bolts (6 mm) 10 - 89
Oil cooler mounting bolts (8 mm) 22 16 -
Oil cooler-to-oil cooler cover bolts 22 16 -
Oil cooler-to-oil cooler cover nuts 22 16 -
EGR cooler coolant supply port cover (M6) 10 - 89
Oil filter housing bolts (Torx) 15 11 -
Oil filter return tube bolt, new base 5 - 44
Oil filter return tube bolt, reinstallation 3 - 27
Crankshaft position (CKP) sensor 11 8 -
Camshaft position (CMP) sensor 11 8 -
Injection control pressure (ICP) sensor 12 9 -
Injection pressure regulator (IPR) valve 50 37 -
Intake air temperature (IAT2) sensor 17 13 -
Exhaust back pressure tube assembly 30 22 -
Exhaust back pressure (EBP) sensor 12 9 -
Exhaust back pressure (EBP) sensor bracket 12 9 -
Lower oil pan bolt 13 10 -
Upper oil pan bolts (M6) 13 10 -
Engine coolant temperature (ECT) sensor 12 9 -
Glow plug 19 14 -
Glow plug relay 11 8 -
High pressure oil pump cover bolts 11 8 -
High pressure oil pump mounting bolts 24 18 -
High pressure oil pump discharge tube mounting bolts (top of pipe) 8 - 71
Rear heat shield (M6 x 1.0 x 1.2) 11 8 -
Rear heat shield (M10 x 1.5 x 16) 49 36 -
Banjo bolt with Copper sealing washers 38 28 -
Banjo bolt with Viton® sealing washers 25 18 -
Fuel filter plug assembly (back of head) 27 20 -
Flywheel/flexplate mounting bolts 94 69 -
Fuel supply and return tubes at filter 43 32 -
Right and left head supply tubes at filter 26 19 -
Front, lifting eye (M10 x30) 41 30 -
Rear, lifting eye (M10 x35) 41 30 -
Automatic transmission tube nut 8 - 71
Engine ground strap bolt 10 - 89
Starter positive cable nut 12 9 -
Starter control wire nut 6 - 53
Torque converter nut 35 26 -
Motor mount nuts 112 83 -
Turbo down pipe bolts 40 30 -
Transmission-to-engine bolts 47 35 -
Transmission tubes mounting bracket bolts 10 - 89
Upper oil pan bolts (M8) 31 23 -
Transmission cooler bolts 8 - 71
Power steering cooler bolts 11 8 -
Battery crossover cable nut 12 9 -
Power steering pump bolt 25 18 -
Battery ground cable-to-engine block bolts 47 35 -
Air conditioning compressor bolts 25 18 -
Two-piece crankcase-to-head tube 82 60 -
A/C manifold bolt 21 15 -
Coolant pump mounting bolt 23 17 -
Coolant pump pulley bolts 31 23 -
Cooling fan stator bolts 40 30 -
Fan clutch hub-to-coolant pump 133 98 -
Belt idler pulley bolts 47 35 -
Belt tensioner bolts 25 18 -
Crankshaft pulley bolts (dual alternators) 47 35 -
Alternator mounting bracket bolts (dual alternators) 47 35 -
Starter mounting bolts 25 18 -
Solenoid wire nut 6 - 53
Battery cable nut 12 9 -
Cylinder block drain plug(4) 20 15 -
Charge air cooler duct clamps (metal duct) 12 9 -
Charge air cooler duct clamps (blow molded duct) 8 - 71
(1) Apply High Temperature Nickel Anti-Seize Lubricant (XL-2) to the threads prior to assembly.
(2) Refer to the procedure in this article.
(3) Apply Threadlock 262 to bolt threads prior to assembly.
(4) Apply clean engine oil to the O-ring seal before installing.
scientia non olet · About LEMON Manuals