LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.0 3, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1417 (Supplemental Inflatable Restraint System) >> Diagnosis And Testing >> Pinpoint Tests - Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Tests >> Pinpoint Test X: DTC B2984 - Deployable Steering Column Circuit Open >> Pinpoint Test X: DTC B2984 - Deployable Steering Column Circuit Open

Pinpoint Test X: DTC B2984 - Deployable Steering Column Circuit Open

WARNING: This page is about a different car, the 2006 Mercury Grand Marquis and 2006 Ford Crown Victoria. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough Inspection and Verification before proceeding with the Pinpoint Test.
  1. X1 CHECK FOR ON-DEMAND AND CONTINUOUS DTCs 
    WARNING: Restraint system diagnostic tools are for service only. Tools must be removed prior to operating the vehicle over the road. Failure to remove restraint system diagnostic tools could result in injury and possible violation of vehicle safety standards.
    WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.
    WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe a pretensioner electrical connector. Doing so could result in pretensioner or air bag deployment and could result in personal injury.
    NOTE: After diagnosing or repairing an SRS, the restraint system diagnostic tools must be removed before operating the vehicle over the road  .
    NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
    • Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
    • Enter the following diagnostic mode on the scan tool: Retrieve/Record Continuous DTCs.
    • Was DTC B2984 retrieved during the on-demand self test? 

    Yes  : This is a hard fault. The fault condition is still present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test. GO to X2.

    No  : This is an intermittent fault. The fault condition is not present at this time. GO to  X6.

  2. X2 CHECK THE DEPLOYABLE STEERING COLUMN 

    Yes  : GO to X3.

    No  : INSTALL a new steering column assembly. REFER to STEERING COLUMN . GO to  X6.

  3. X3 CHECK CIRCUIT 2136 (OG) FOR AN OPEN 
    • Key in OFF position.
    • Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RCM C310a and C310b.
    • Disconnect: Restraint System Diagnostic tool 418-F395 from the Deployable Steering Column C2318.
    • Measure the resistance between RCM (J310a-21, circuit 2136 (OG), harness side and deployable steering column C2318, circuit 2136 (OG), harness side.
      Fig 1: Measuring Resistance Between RCM (J310A-21, Circuit 2136 (OG), Harness Side And Deployable Steering Column C2318, Circuit 2136
      G04586444Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohms? 

    Yes  : GO to X4.

    No  : REPAIR circuit 2136 (OG). GO to  X7.

  4. X4 CHECK CIRCUIT 2137 (RD/LB) FOR AN OPEN 
    • Measure the resistance between RCM C310a-22, circuit 2137 (RD/LB), harness side and deployable steering column C2318, circuit 2137 (RD/LB), harness side.
      Fig 2: Measuring Resistance Between RCM C310A-22, Circuit 2137 And Deployable Steering Column C2318, Circuit 2137
      G04586445Courtesy of FORD MOTOR CO.
    • Is the resistance less than 0.5 ohm? 

    Yes  : GO to X5.

    No  : REPAIR open in circuit 2137 (RD/LB). GO to  X7.

  5. X5 CONFIRM THE RCM FAULT 
    NOTE: Make sure all restraint system diagnostic tools, sensor electrical connectors and the RCM electrical connectors are connected before carrying out the on-demand self test. If not, erroneous DTCs will be recorded.
    • Key in OFF position.
    • Connect: Restraint System Diagnostic Tool 418-F395 to the Deployable Steering Column C2318.
    • Repower the system. Do not  prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
    • Was DTC B2984 retrieved during the on-demand self test? 

    Yes  : INSTALL a new RCM . REFER to RESTRAINTS CONTROL MODULE (RCM) . GO to  X7.

    No  : CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to  X7.

  6. X6 CHECK FOR AN INTERMITTENT FAULT 

    Yes  : This is a hard fault. The fault condition is now present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test. GO to  X3.

    No  : CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to X7.

  7. X7 CHECK FOR ADDITIONAL DTCs 
    • Refer to the continuous DTCs recorded during Step  X1.
    • Were any continuous DTCs retrieved during Step   X1 ? 

    Yes  : Do not clear any DTCs until all DTCs have been resolved. GO to the RESTRAINTS CONTROL MODULE (RCM) DIAGNOSTIC TROUBLE CODE (DTC) PRIORITY TABLE  in this article for pinpoint test direction.

    No  : RECONNECT the system. If previously directed to deactivate the system, REACTIVATE the system. REFER to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEACTIVATION AND REACTIVATION . REPOWER the system. REFER to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING . PROVE OUT the system. CLEAR all DTCs.

scientia non olet · About LEMON Manuals