LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 1992 >> Crown Victoria Base, AOD >> Repair and Diagnosis >> External Pages >> Different car >> Section 4 (1.9L 4-CYL - VIN [J]) >> Torque Specifications

Torque Specifications

WARNING: This page is about a different car, the 1992 Mercury Tracer, 1992 Ford Escort, 1991 Mercury Tracer, and 1991 Ford Escort. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
A/C Compressor Mounting Bolt 15-22 (20-30)
Axle Shaft Nut 174-235 (236-319)
Belt Tensioner Bolt 17-22 (23-30)
Cam Position Sensor Bolt 15-22 (20-30)
Camshaft Sprocket-To-Camshaft Bolt 70-85 (95-115)
Connecting Rod Cap Nut 26-30 (35-41)
Crankshaft Damper Bolt 81-96 (110-130)
Crankshaft Rear Seal Retainer Bolt 15-22 (20-30)
Crossmember Bolt/Nut 47-66 (64-90)
Cylinder Head Bolts (1)
Step 1 30-44 (41-60)
Step 2 Loosen All Bolts 2 Turns
Step 3 44 (60)
Step 4 Additional 90 Degrees
Step 5 Additional 90 Degrees
Exhaust Manifold Nut 16-19 (22-26)
Extension Bar-To-Transaxle Nut 23-34 (31-46)
Flywheel Bolt 54-67 (73-91)
Intake Manifold Nut 12-15 (16-20)
Lower Ball Joint Clamp Bolt 32-43 (43-58)
Main Bearing Cap Bolt 67-80 (91-109)
Oil Filter Adapter-To-Oil Pump 21-26 (29-35)
Oil Galley Plug 12 (16)
Oil Pan Bolt (2)
Oil Pump-To-Cylinder Block Bolt 11 (15)
Power Steering Pump
Mounting Bolt 27-40 (37-54)
Mounting Nut 23-34 (31-46)
Rocker Arm Bolt 17-22 (23-30)
Shift Control Rod-To-Transaxle Bolt 12-17 (16-23)
Spark Plug 15 (20)
Tie Rod Nut 31-43 (42-58)
Torque Converter Nut 25-36 (34-49)
Transaxle-To-Crossmember Nut 27-38 (37-52)
Transaxle-To-Engine Bolt 40-59 (54-80)
Water Pump Bolt 15-22 (20-30)
Wheel Lug Nut 65-87 (88-118)
INCH Lbs. (N.m) 
Air By-Pass Valve-To-Throttle Body Bolt 72-97 (7-11)
Camshaft Thrust Plate Bolt 72-108 (7-12)
Crank Angle Sensor-To-Oil Pump Bolt 24-30 (2-3)
Oil Pump Pick-Up Tube Bolt 84-114 (9-13)
Thermostat Housing Bolt 72-108 (7-12)
Timing Belt Cover Nut 36-60 (4-6)
Timing Belt Cover Stud-To-Cylinder Block 84-108 (9-12)
Valve Cover Bolt 48-108 (5-12)
(1) Tighten bolts in sequence. See Figure.
(2) Tighten bolts using following procedure: Pan-to-transaxle 10 mm bolts to 30-40 ft. lbs. (41-54 N.m). Loosen pan-to-transaxle 10 mm bolts 1/2 turn. Pan-to-block bolts to 15-22 ft. lbs. (20-30 N.m). See Figure. Pan-to-transaxle 10 mm bolts to 30-40 ft. lbs. (41-54 N.m).