LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 1992 >> Crown Victoria Base, AOD >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> 4.6L V8 - VIN [W] >> Torque Specifications

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Camshaft Sprocket Bolt 81-95 (110-129)
Chain Tensioner Bolt 15-22 (20-30)
Connecting Rod Bolt (1)
Step 1 18-25 (24-34)
Step 2 Additional 85-95 Degrees
Crankshaft Damper Bolt 114-121 (155-164)
Cylinder Block-To-Transmission Support Brace Bolt 18-31 (24-42)
Cylinder Head Bolt (1)(2)
Step 1 15-22 (20-30)
Step 2 Additional 85-95 Degrees
Step 3 Additional 85-95 Degrees
EGR Tube Fitting-To-Exhaust Manifold 33-48 (45-65)
EGR Tube-to-Exhaust Manifold 26-33 (35-45)
EGR Valve-To-Intake Manifold Bolt 15-22 (20-30)
Engine Mount Through Bolt 22-25 (30-34)
Exhaust Manifold Bolt (3) 15-22 (20-30)
Flexplate-To-Crankshaft Bolt 54-64 (73-87)
Front Cover Bolt/Stud 15-22 (20-30)
Intake Manifold Bolt (4) 15-22 (20-30)
Main Bearing Cap Bolt (1)(5)
Step 1 22-25 (30-34)
Step 2 Additional 85-95 Degrees
Main Bearing Cap Side Bolt (1)(5)
Step 1 (6)
Step 2 14-17 (19-23)
Oil Filter Adapter 15-22 (20-30)
Oil Pan Bolt 15-22 (20-30)
Oxygen Sensor 27-33 (37-45)
Pick-Up Tube-To-Main Bearing Cap Nut 15-22 (20-30)
Power Steering Pump-To-Mount Nut 15-22 (20-30)
Thermostat Housing Bolt 15-22 (20-30)
Torque Converter Nut 20-34 (27-46)
Transmission-To-Cylinder Block Bolt 40-50 (54-68)
Water Pump Bolt 15-22 (20-30)
Water Pump Pulley Bolt 15-22 (20-30)
INCH Lbs. (N.m) 
Air By-Pass Valve Bolt 72-102 (8-11)
Camshaft Cap Bolt (7) 72-106 (8-12)
Camshaft Cover Bolt 72-106 (8-12)
Chain Guide Bolt 72-106 (8-12)
Crankshaft Seal Retainer Bolt 72-106 (8-12)
Fuel Pressure Regulator Bolt 27-40 (3-4)
Fuel Rail Bolt 72-102 (8-11)
Ignition Wire Tray-To-Coil Bracket Bolt 72-106 (8-12)
Main Bearing Cap Jack Screw (5)
Step 1 44 (5)
Step 2 80-97 (9-10)
Oil Pump-To-Cylinder Block Bolt 72-106 (8-12)
Pick-Up Tube-To-Oil Pump Bolt 72-106 (8-12)
Throttle Body Bolt 72-102 (8-11)
(1) Use new bolts. DO NOT  reuse bolts.
(2) Tighten bolts in sequence. See Figure.
(3) Tighten bolts in sequence. See Figure.
(4) Tighten bolts in sequence. See Figure. Bolts must be retorqued to specification once engine reaches normal operating temperature.
(5) Tighten bolts in sequence. See Figure.
(6) Tighten bolts to 84 INCH lbs. (10 N.m).
(7) Tighten bolts in sequence. See Figure.