Diagnostic Test

CHECK FOR RELATED DTCs
1. Ignition on, engine not running.
2. With the scan tool, read HVAC DTCs.
  Are there any Door Control Circuit Open, Performance, or Short to Ground, Voltage, or Together DTCs present?
  
  Yes
  - Go To DTC TROUBLESHOOTING and perform the appropriate diagnostic procedure.
  No
  - Go To 2
CHECK FOR AN ACTIVE DTC
1. With the scan tool, read HVAC DTCs and record on the repair order.
2. Record the Environmental Data.
3. With the scan tool, erase DTCs.
4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read HVAC DTCs.
  Did the DTC return?
  
  Yes
  - Go To 3
  No
  - Perform the INTERMITTENT CONDITIONS TEST. Refer to TESTING FOR AN INTERMITTENT CONDITION .
PERFORM HVAC ACTUATOR CALIBRATION TEST
1. With the scan tool, perform the HVAC Actuator Calibration Test.
  Did this DTC change from Stored to Active while performing the HVAC System Test?
  
  Yes
  - Go To 4
  No
  - Go To 6
CHECK THE DRIVER BLEND DOOR
1. Remove the Driver Blend Door Actuator and check the Driver Blend Door stops, linkage (stripped or cracked) and door. Refer to ACTUATOR, BLEND DOOR, REMOVAL AND INSTALLATION .
  Were there any problems found?
  
  Yes
  - Repair or replace the Driver Blend Door as necessary in accordance with the Service Information.
  - Perform the HVAC VERIFICATION TEST. Refer to HVAC VERIFICATION TEST .
  No
  - Go To 5
CHECK THE DRIVER BLEND DOOR ACTUATOR
1. Replace the Driver Blend Door Actuator in accordance with the Service Information. Refer to ACTUATOR, BLEND DOOR, REMOVAL AND INSTALLATION .
2. With the scan tool, erase HVAC DTCs and perform the HVAC Actuator Calibration Test.
  Did this DTC reset?
  
  Yes
  - Go To 6
  No
  - Test complete.
  - Perform the HVAC VERIFICATION TEST. Refer to HVAC VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all HVAC Module harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all HVAC Module harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read HVAC Module DTCs.
  Did the DTC return?
  
  Yes
  - Replace the HVAC Module in accordance with the Service information. Refer to MODULE, HVAC, REMOVAL AND INSTALLATION .
  - Perform the HVAC MODULE VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Perform the HVAC MODULE VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  - Test complete.