LEMON Manuals: Even more car manuals for everyone
Home >> Fiat >> 2017 >> 500 Pop, Standard Trans >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Entertainment Systems >> (Entertainment TELEMATIC Module (ETM) - Electrical Diagnostics - 500 - Except Electric) >> DTC Troubleshooting >> B143D-12 Microphone 2 - Circuit Short To Battery >> Diagnostic Test

Diagnostic Test

  1. CHECK FOR AN ACTIVE DTC 
    NOTE:

    Verify the connection of the Rearview Mirror harness connector.

    1. Turn the ignition on.
    2. With the scan tool, read Entertainment Telematic Module (ETM/LTM) DTCs and record on the repair order.
    3. With the scan tool, erase DTCs.
    4. With the scan tool, read (ETM/LTM) DTCs.

      Did the DTC return?

      Yes 

      • Go To  2

      No 

  2. CHECK THE REARVIEW MIRROR 
    1. Turn the ignition off.
    2. Disconnect the Rearview Mirror harness connector.
    3. With the scan tool, erase (ETM/LTM) DTCs.
    4. Turn the ignition on.
    5. Wait 10 seconds.
    6. With the scan tool, read (ETM/LTM) DTCs.

      Did the DTC return?

      Yes 

      • Go To  3

      No 

      • Replace the Rearview Mirror in accordance with the service information.
      • Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  3. CHECK THE MICROPHONE 2 IN (+) CIRCUIT FOR A SHORT TO VOLTAGE 
    1. Turn the ignition off.
    2. Disconnect the (ETM/LTM) C1 harness connector.
    3. Turn the ignition on.
    4. Measure the voltage between ground and the (X722) Microphone 2 IN (+) circuit at the (ETM/LTM) C1 harness connector.

      Is there any voltage present?

      Yes 

      • Repair the (X722) Microphone 2 IN (+) circuit for a short to voltage.
      • Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .

      No 

      • Go To  4
  4. CHECK THE MICROPHONE 2 IN (-) CIRCUIT FOR A SHORT TO VOLTAGE 
    1. Measure the voltage between ground and the (X723) Microphone 2 IN (-) circuit at the (ETM/LTM) C1 harness connector.

      Is there any voltage present?

      Yes 

      • Repair the (X723) Microphone 2 IN (-) circuit for a short to voltage.
      • Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .

      No 

      • Go To  5
  5. CHECK RELATED HARNESS CONNECTIONS 
    1. Disconnect all (ETM/LTM) harness connectors.
    2. Disconnect all related in-line harness connections (if equipped).
    3. Disconnect the related component harness connectors.
    4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Perform a terminal drag test on each connector terminal to verify proper terminal tension.

      Repair any conditions that are found.

    5. Reconnect all (ETM/LTM) harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. With the scan tool, erase DTCs.
    9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
    10. With the scan tool, read (ETM/LTM) DTCs.

      Did the DTC return?

      Yes 

      • Replace the ETM in accordance with the service information. Refer to REMOVAL .
      • Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .

      No 

scientia non olet · About LEMON Manuals