LEMON Manuals: Even more car manuals for everyone
Home >> Fiat >> 2016 >> 500 c Easy, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 24 (1.4L 16-Valve Engine (Service Information) 500) >> Engine Mounting >> Bracket, Engine Mount, Right >> Installation >> Installation

Bracket, Engine Mount, Right: Installation: Installation

WARNING: This page is about a different car, the 2015 Fiat 500. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: RH Engine Mount Bracket & Bolts
GC0152463Courtesy of CHRYSLER GROUP, LLC
  1. Install the RH engine mount bracket (1) with six bolts (2) tightened to 25 N.m (18 ft. lbs.).
    Fig 2: Upper Timing Belt Cover & Bolts
    GC0152466Courtesy of CHRYSLER GROUP, LLC
  2. Install the upper timing belt cover (1) with two bolts (2 and 3) tightened to 9 N.m (80 in. lbs.).
    Fig 3: RH Engine Mount Isolator, Support Bracket & Bolts With Tightening Sequence
    GC0153367Courtesy of CHRYSLER GROUP, LLC
  3. Install the RH engine mount isolator (3) and support bracket (1) to the engine mount bracket with three bolts. Tighten the isolator to engine bracket bolts in the sequence shown in illustration to 60 N.m (44 ft. lbs.).
  4. Install the RH engine mount isolator (3) to the body with three bolts (2). Tighten the isolator to body bolts (2) to 60 N.m (44 ft. lbs.).
    Fig 4: Return Hose, Lower Supply Hose, Mounting Screw & Coolant Recovery Bottle
    GC0152348Courtesy of CHRYSLER GROUP, LLC
  5. Install the pressurized coolant bottle (5). Refer to BOTTLE, PRESSURIZED COOLANT, INSTALLATION .
    Fig 5: Tunnel Support Brace & Bolts
    GC0152449Courtesy of CHRYSLER GROUP, LLC
  6. Raise and support the vehicle. Refer to HOISTING .
  7. Install the tunnel support brace (2) with four bolts (1) tightened to 90 N.m (60 ft. lb.).
    Fig 6: Rear Engine Mount Bracket, Isolator & Fasteners
    GC0153301Courtesy of CHRYSLER GROUP, LLC
  8. If equipped with a manual transmission, install the rear engine mount isolator (7) to the transmission with the rear engine mount bracket bolt (3) and nut (6) tightened to 80 N.m (59 ft. lbs.) and tighten the isolator bolt (1) to 130 N.m (96 ft. lbs.).
    Fig 7: Two Bolts Of Lower Transmission Mount
    GC0152406Courtesy of CHRYSLER GROUP, LLC
  9. If equipped with an automatic transmission, install the rear engine mount isolator (5) in the bracket (3) with two bolts (4) tighten to 60 N.m (44 ft. lbs.). Install the isolator bolt (1) and tighten to 130 N.m (96 ft. lbs.).
    Fig 8: Lower Air Dam/Belly Pan
    GC0082359Courtesy of CHRYSLER GROUP, LLC
  10. Install the belly pan. Refer to BELLY PAN, INSTALLATION .
    Fig 9: Fuel Line, Hose Retainer & Fuel Vapor Purge Hose
    GC0152408Courtesy of CHRYSLER GROUP, LLC
  11. Lower the vehicle.
  12. Connect the fuel vapor purge hose (3) to the intake manifold.
  13. Connect the fuel line (2) to the fuel rail and close the hose retainer (1). Refer to FITTING, QUICK CONNECT .
    Fig 10: Air Cleaner Body Assembly
    GC0152416Courtesy of CHRYSLER GROUP, LLC
  14. Install the air cleaner body (6). Refer to BODY, AIR CLEANER, INSTALLATION .
    Fig 11: Engine Cover
    GC0152354Courtesy of CHRYSLER GROUP, LLC
  15. Connect the negative battery cable and tighten nut to 5 N.m (45 in. lb.).
  16. Install the engine cover (1).
  17. Run the engine until it reaches normal operating temperature. Check cooling system for correct fluid level. Refer to STANDARD PROCEDURE .
scientia non olet · About LEMON Manuals