LEMON Manuals: Even more car manuals for everyone
Home >> Fiat >> 2016 >> 500 Turbo, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 9 ((Antilock Brake System (Abs) - Electrical Diagnostics - 500 - Electric)) >> DTC Troubleshooting >> C0037-01-Left Rear Speed Sensor - General Electrical Failure >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different variant/trim than selected.
  1. CHECK FOR AN ACTIVE DTC 
    NOTE:

    This DTC must be active for the results of this test to be valid.

    1. Turn the ignition on.
    2. With the scan tool, read ABS DTCs and record on the repair order.
    3. With the scan tool, erase ABS DTCs.
      CAUTION:

      Make sure brake capability is available before road testing.

    4. Road test the vehicle over 40 km/h (25 mph).
      NOTE:

      Vehicle must be driven above 40 km/h (25 mph) for two minutes before set conditions are met.

    5. With the scan tool, read ABS DTCs.

      Did the DTC return?

      Yes 

      • Go To  2

      No 

      • The condition that caused the symptom is currently not present. Inspect the related wiring for a possible intermittent condition. Look for any chafed, pierced, pinched, or partially broken wires.
      • Perform the ABS INTERMITTENT CONDITION TEST. Refer to ABS INTERMITTENT CONDITION  .
  2. CHECK CONNECTOR/TERMINAL FOR DAMAGE 
    NOTE:

    Check all terminals for broken, bent, pushed out, or corroded terminals.

    1. Turn the ignition off.
    2. Inspect the Wheel Speed Sensor for proper mounting.
    3. Inspect the Wheel Speed Sensor harness and connector.
    4. Inspect the Wheel Speed Sensor for excessive debris on the sensor.

      Were any problems found?

      Yes 

      • Repair as necessary in accordance with the Service Information.
      • Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST  .

      No 

      • Go To  3
  3. CHECK (B4) LEFT REAR WHEEL SPEED SENSOR SIGNAL CIRCUIT VOLTAGE 
    1. Disconnect the Left Rear Wheel Speed Sensor harness connector.
    2. Turn the ignition on.
    3. Measure the voltage between the (B4) Left Rear Wheel Speed Sensor Signal circuit and ground.

      Is the voltage above 10 volts?

      Yes 

      • Go To  6

      No 

      • Go To  4
  4. (B4) LEFT REAR WHEEL SPEED SENSOR SIGNAL CIRCUIT SHORTED TO GROUND 
    1. Turn the ignition off.
    2. Disconnect the ABS Module harness connector.
    3. Measure the resistance between the (B4) Left Rear Wheel Speed Sensor Signal circuit and ground.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Repair the (B4) Left Rear Wheel Speed Sensor Signal circuit for a short to ground.
      • Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST  .

      No 

      • Go To  5
  5. (B4) LEFT REAR WHEEL SPEED SENSOR SIGNAL CIRCUIT OPEN 
    1. Measure the resistance of the (B4) Left Rear Wheel Speed Sensor Signal circuit between the Left Rear Wheel Speed Sensor harness connector and the ABS harness connector.

      Is the resistance below 5 Ohms?

      Yes 

      • Go To  6

      No 

      • Repair the open (B4) Left Rear Wheel Speed Sensor Signal circuit.
      • Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST  .
  6. (B3) LEFT REAR WHEEL SPEED SENSOR SUPPLY CIRCUIT SHORTED TO VOLTAGE 
    1. Turn the ignition on.
    2. Measure the voltage of the (B3) Left Rear Wheel Speed Sensor Supply circuit at the Left Rear Wheel Speed Sensor harness connector.

      Is there any voltage present?

      Yes 

      • Repair the (B3) Left Rear Wheel Speed Sensor Supply circuit for a short to voltage.
      • Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST  .

      No 

      • Go To  7
  7. (B3) LEFT REAR WHEEL SPEED SENSOR SIGNAL CIRCUIT SHORTED TO GROUND 
    1. Turn the ignition off.
    2. Measure the resistance between the (B3) Left Rear Wheel Speed Sensor Supply circuit and ground.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Repair the (B3) Left Rear Wheel Speed Sensor Supply circuit for a short to ground.
      • Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST  .

      No 

      • Go To  8
  8. (B3) LEFT REAR WHEEL SPEED SENSOR SIGNAL CIRCUIT OPEN 
    1. Measure the resistance of the (B3) Left Rear Wheel Speed Sensor Supply circuit between the Left Rear Wheel Speed Sensor harness connector and the ABS harness connector.

      Is the resistance below 5 Ohms?

      Yes 

      • Go To  9

      No 

      • Repair the open (B3) Left Rear Wheel Speed Sensor Supply circuit.
      • Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST  .
  9. (B4) LEFT REAR WHEEL SPEED SENSOR SUPPLY CIRCUIT SHORTED TO THE (B3) LEFT REAR WHEEL SPEED SENSOR SIGNAL CIRCUIT 
    1. Turn the ignition off.
    2. Measure the resistance between the (B3) Left Rear Wheel Speed Sensor Supply circuit and the (B4) Left Rear Wheel Speed Sensor Signal circuit at the ABS Module harness connector.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Repair (B3) Left Rear Wheel Speed Sensor Supply circuit for a short to the (B4) Left Rear Wheel Speed Sensor Signal circuit.
      • Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST  .

      No 

      • Go To  10
  10. LEFT REAR WHEEL SPEED SENSOR 
    1. Replace the Left Rear Wheel Speed Sensor in accordance with the Service Information. Refer to SENSOR, WHEEL SPEED, REAR, REMOVAL .
    2. Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST  .
      CAUTION:

      Make sure braking capability is available before road testing.

    3. Road test the vehicle over 40 km/h (25 mph).
      NOTE:

      Vehicle must be driven above 40 km/h (25 mph) for set conditions to be meet.

    4. With the scan tool, read ABS DTCs.

      Is the status Active for this DTC?

      Yes 

      No 

      • Test complete.
scientia non olet · About LEMON Manuals