LEMON Manuals: Even more car manuals for everyone
Home >> Fiat >> 2016 >> 500 Turbo, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 5 (Occupant Restraint Controller (Orc) - DTCS B0101-16 To B0116-1B - 500 - Electric) >> DTC Troubleshooting >> B0111-64-Driver Remote Acceleration Sensor (Satellite) - Signal Plausibility Failure >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different variant/trim than selected.
  1. VERIFY THAT DTC B0111-64-DRIVER REMOTE ACCELERATION SENSOR (SATELLITE) - SIGNAL PLAUSIBILITY FAILURE IS ACTIVE 
    WARNING:

    Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    NOTE:

    Using the wiring diagram/schematic as a guide check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals, and correct pin tension.

    NOTE:

    If after the harness inspection it appears the impact sensor connector is only seated halfway. Reseat the harness connector into the impact sensor and lock the tab.

    WARNING:

    Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    NOTE:

    Make sure the battery is fully charged.

    1. Turn the ignition on.
    2. With the scan tool, read ORC DTCs.

      Does the scan tool display active: B0111-64-DRIVER REMOTE ACCELERATION SENSOR (SATELLITE) - SIGNAL PLAUSIBILITY FAILURE - DTC?

      Yes 

      • Go To  2

      No 

  2. CHECK THE (R130) AND (R150) LEFT SIDE IMPACT SENSOR 1 CIRCUITS FOR A SHORT TO BATTERY 
    WARNING:

    Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    1. Disconnect the Left Side Impact Sensor 1 harness connector.
    2. Disconnect the ORC harness connectors.
      NOTE:

      Check connectors - Clean and repair as necessary.

      NOTE:

      Probing of the circuit cavities at the ORC Module body harness connectors is only to be done with a approved test lead from the (special tool #10159, Test Leads, Dedicated), test lead 10159-6. Or a comparable test lead to prevent vehicle wiring harness connector damage during diagnostic procedures.

    3. Connect the test probes to the appropriate ORC harness connector terminal(s).
      WARNING:

      Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    4. Measure the voltage of the (R130) Left Side Impact Sensor 1 Signal circuit and the (R150) Sensor 1 Ground circuit at the Left Side Impact Sensor 1 harness connector.

      Is there any voltage present?

      Yes 

      • Repair the (R130) and (R150) Left Side Impact Sensor 1 circuits for a short to battery.
      • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .

      No 

      • Go To  3
  3. CHECK THE (R130) AND (R150) LEFT SIDE IMPACT SENSOR 1 CIRCUITS FOR A SHORT TO GROUND 
    WARNING:

    Turn the ignition on, then reconnect the battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    1. Measure the resistance between ground and the (R130) Left Side Impact Sensor 1 Signal circuit at the Left Side Impact Sensor 1 harness connector.
    2. Measure the resistance between ground and the (R150) Left Side Impact Sensor 1 Ground circuit at the Left Side Impact Sensor 1 harness connector.

      Is the resistance below 100K Ohms on either circuit?

      Yes 

      • Repair the (R130) and (R150) Left Side Impact Sensor 1 Signal and Ground circuit for a short to ground.
      • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .

      No 

      • Go To  4
  4. CHECK THE (R130) AND (R150) LEFT SIDE IMPACT SENSOR 1 CIRCUITS FOR A SHORT TOGETHER 
    1. Measure the resistance between the (R130) Left Side Impact Sensor 1 Signal circuit and the (R150) Sensor 1 Ground circuit at the Left Side Impact Sensor 1 harness connector.

      Is the resistance below 100K Ohms?

      Yes 

      • Repair the (R130) and (R150) Left Side Impact Sensor 1 circuits shorted together.
      • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .

      No 

      • Go To  5
  5. CHECK THE (R150) LEFT SIDE IMPACT SENSOR 1 GROUND CIRCUIT FOR AN OPEN OR HIGH RESISTANCE 
    1. Measure the resistance of the (R150) Left Side Impact Sensor 1 Ground circuit at the Left Side Impact Sensor 1 harness connector.

      Is the resistance below 1 Ohm?

      Yes 

      • Go To  6

      No 

      • Repair the (R150) Left Side Impact Sensor 1 Ground circuit for an open or high resistance.
      • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .
  6. CHECK THE (R130) LEFT SIDE IMPACT SENSOR 1 SIGNAL CIRCUIT FOR AN OPEN OR HIGH RESISTANCE 
    1. Measure the resistance of the (R130) Left Side Impact Sensor 1 Signal circuit at the Left Side Impact Sensor 1 harness connector.

      Is the resistance below 1 Ohm?

      Yes 

      • Go To  7

      No 

      • Repair the (R130) Left Side Impact Sensor 1 Signal circuit for an open or high resistance.
      • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .
  7. CHECK OPERATION OF THE LEFT SIDE IMPACT SENSOR 1 
    1. Replace the Left Side Impact Sensor 1. Refer to SENSOR, IMPACT, REMOVAL .
    2. Reconnect the vehicle body harness to the impact sensor.
    3. Remove any special tools or jumper wires and reconnect all previously disconnected components - except the Battery.
      WARNING:

      Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    4. Connect the scan tool to the Data Link Connector - use the most current software available.
    5. Use the scan tool and erase the stored codes in all airbag system modules.
    6. Turn the Ignition Off, and wait 15 seconds before turning the Ignition On.
    7. Wait one minute, and read active codes and if there are none present read the stored codes.

      Did the active Left Side Impact Sensor 1 DTC return?

      Yes 

      • Go To  8

      No 

  8. REPLACE THE OCCUPANT RESTRAINT CONTROLLER 
    WARNING:

    Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    WARNING:

    If the airbag control module is dropped at any time, it must be replaced. Failure to take the proper precautions could result in accidental airbag deployment and serious or fatal injury.

    If there are no possible causes remaining, view repair.

    Repair 

scientia non olet · About LEMON Manuals