Diagnostic Test

WARNING: This page is about a different car, the 2015 Fiat 500. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR AN ACTIVE DTC
1. Diagnose and repair any other active component or circuit DTCs before continuing with this procedure.
2. Turn the ignition on.
3. With the scan tool, read DTCs, Copy DTC and Freeze Frame information.
4. Operate the vehicle under conditions similar to which the DTC was set.
  Are there excessive misfires shown or is the DTC pending at this time?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK THE (K42) KNOCK SENSOR SIGNAL CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Turn the ignition off.
2. Disconnect the Knock Sensor harness connector.
3. Disconnect the PCM C2 harness connector.
4. Measure the resistance of the (K42) Knock Sensor Signal circuit from the Knock Sensor harness connector to the PCM C2 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 3
  No
  - Repair the (K42) Knock Sensor Signal circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST, 16V Turbo .
CHECK THE (K942) KNOCK SENSOR RETURN CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Measure the resistance of the (K942) Knock Sensor Return circuit from the Knock Sensor harness connector to the PCM C2 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 4
  No
  - Repair the (K942) Knock Sensor Return circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST, 16V Turbo .
KNOCK SENSOR
1. Turn the ignition off.
2. Verify that there is good pin to terminal contact at the Knock Sensor and the Powertrain Control Module connectors.
3. If no problems were found in the connectors, replace the Knock Sensor. Refer to SENSOR, KNOCK, REMOVAL .
4. Reconnect the PCM C2 harness connector.
5. Turn the ignition on.
6. With the scan tool, erase DTCs.
7. Turn the ignition on.
8. With the scan tool, read DTCs.
  Is the DTC active or pending?
  
  Yes
  - Go To 5
  No
  - Test complete.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST, 16V Turbo .
CHECK RELATED PCM AND COMPONENT CONNECTIONS
1. Perform any Service Bulletins that apply.
2. Disconnect all PCM harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
11. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Powertrain Control Module in accordance with the Service information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST, 16V Turbo .
  No
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST, 16V Turbo .
  - Test complete.