LEMON Manuals: Even more car manuals for everyone
Home >> Fiat >> 2016 >> 500 Turbo, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 25 (1.4L 16-Valve Turbo Engine (Service Information) 500) >> Lubrication >> Pan, Oil >> Installation >> With Manual Transmission

With Manual Transmission

WARNING: This page is about a different car, the 2015 Fiat 500. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Oil Pan Sealant Locations
GC0152689Courtesy of CHRYSLER GROUP, LLC
  1. Clean the oil pan, engine block, oil pump and rear seal retainer mating surfaces with isopropyl alcohol in preparation for sealant application.
    CAUTION:

    Engine assembly requires the use of a unique sealant that is compatible with engine oil. Using a sealant other than Mopar® Engine Sealant RTV Silicone Rubber Adhesive may result in engine fluid leakage.

    CAUTION:

    Following the application of Mopar® Engine Sealant RTV Silicone Rubber Adhesive to the gasket surfaces, the components must be assembled within 10 minutes and the attaching fasteners must be tightened to specification within the next 10 minutes. Prolonged exposure to the air prior to assembly may result in engine fluid leakage.

  2. Apply a 2 to 3 mm wide bead of Mopar® Engine Sealant RTV Silicone Rubber Adhesive to the oil pan as shown in illustration in the following locations:
    • Oil pan to engine block flange (1)
    • Two oil pump to engine block T-joints (3)
    • Two rear seal retainer to engine block T-joints (2)
    Fig 2: Flywheel Dust Cover & Bolt
    GC0153316Courtesy of CHRYSLER GROUP, LLC
  3. Install the flywheel dust cover (2) to the oil pan. Tighten the bolt (1) to 9 N.m (80 in. lbs.).
    Fig 3: Oil Pan Flange Fasteners
    GC0152688Courtesy of CHRYSLER GROUP, LLC
  4. Install the oil pan with fourteen bolts (1), two studs and two nuts (2) hand tight.
    Fig 4: Transmission Bell Housing Bolts, Transmission Stud, Flywheel Dust Cover & Nut
    GC0155729Courtesy of CHRYSLER GROUP, LLC
  5. Install the two lower transmission bell housing bolts (2) and tighten to 40 N.m (30 ft. lbs.).
  6. Install the three bolts (1) to the flywheel dust cover and tighten to 9 N.m (80 in. lbs.).
    Fig 5: Oil Pan Fastener Tightening Sequence
    GC0152690Courtesy of CHRYSLER GROUP, LLC
  7. Tighten the sixteen oil pan fasteners in two steps following the sequence shown in illustration:
    • Step 1: All to 4 N.m (35 in. lbs.).
    • Step 2: All to 9 N.m (80 in. lbs.).
  8. Install the rear engine mount. Refer to INSULATOR, ENGINE MOUNT, REAR, INSTALLATION .
    Fig 6: Front Exhaust Pipe Support Bolt & Flange Nuts
    GC0153120Courtesy of CHRYSLER GROUP, LLC
  9. Install a new catalytic converter to front exhaust pipe gasket.
  10. Install the front exhaust pipe to the catalytic converter with two nuts tightened to 56 N.m (41 ft. lbs.).
  11. Install the front exhaust pipe support bolt (2) and tighten to 56 N.m (41 ft. lbs.).
  12. Install the exhaust flange nuts (1) and tighten to 69 N.m (51 ft. lbs.).
    Fig 7: Tunnel Support Brace & Bolts
    GC0152449Courtesy of CHRYSLER GROUP, LLC
  13. Install the tunnel support brace (2) with four bolts (1) tightened to 90 N.m (60 ft. lb.).
    Fig 8: Lower Air Dam/Belly Pan
    GC0082359Courtesy of CHRYSLER GROUP, LLC
  14. Install the belly pan. Refer to BELLY PAN, INSTALLATION .
  15. If removed, install the oil filter and fill the engine crankcase with the proper oil to the correct level. Refer to STANDARD PROCEDURE .
  16. Connect the negative battery cable and tighten nut to 5 N.m (45 in. lbs.).
  17. Start and run the engine until it reaches normal operating temperature.
scientia non olet · About LEMON Manuals