Gap And Flush: Specifications: Specifications

WARNING: This page is about a different car, the 2015 Fiat 500. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Gap And Flush Measurement Areas

Courtesy of CHRYSLER GROUP, LLC

Base model shown in illustration, other models typical unless noted.

NOTE:

All measurements are in millimeters

U/D = Up/Down
O/F = Over Flush
U/F = Under Flush
F/A = Fore/Aft

DIMENSION	DESCRIPTION	GAP	FLUSH
1	Hood to Fascia	4.0+/- 1.0	Fascia U/F 2.0+/- 1.0
		Parallel within 1.0
2	Fender to Hood	4.0+/- 1.0	Fender U/F 2.0+/- 0.0 @ Front
		Parallel within 0.7	Fender U/F 0.0+/- 1.0 @ Rear
3	Windshield to Body Side	4.0+/- 1.5	Body Side O/F 5.5 +/- 1.5
4	Windshield to Roof	3.5 +/- 1.0	Glass U/F 2.6 +/- 1.5
		Parallel within 1.0
5	Fuel Filler to Body Side	3.0 +/- 0.8	Door U/F 0.8+/- 0.8
		Parallel within 0.6
6	Door to Body Side	4.0+/- 0.8	Door O/F 0.5 +/- 0.5
	Feature Line 0.0 +/- 0.5	Parallel within 0.7
7	Door to Body Side Sill	4.5 +/- 1.0	-
		Parallel within 0.7	-
8	Fender to Door	4.0+/- 0.6	Fender O/F 0.5 +/- 0.5
	Feature Line 0.0 +/- 0.5	Parallel within 0.5
9	Headlamp to Fender	2.0 +/- 0.8	-
		Parallel within 0.7	-
10	Headlamp to Fascia	@ Hood 4.0 +/- 0.7	-
		@ Fender 2.0 +/- 0.7	-
11	Backlight to Liftgate	3.5 +/- 1.5	-
		Parallel within 1.0	-
12	Liftgate to Body Side	4.0 +/- 1.0	Liftgate 1.0 U/F +/- 0.7
		Parallel within 0.7
13	Liftgate to Roof	6.0 +/- 0.5	Liftgate 1.0 U/F +/- 1.0
		Parallel within 0.7
14	Liftgate to Body Side	4.2 +/- 1.0	Body Side 4.2 O/F +/- 0.7
15	Roof to Rap Joint Molding	0.0 +/- 0.5	Roof 2.2 O/F +/- 1.0
16	Door Glass Run (outer) to Body Side	0.0 +/- 1.0	0.0 +/- 1.0
17	Door Flag Applique to Fender Applique	4.0 +/- 0.6	Fender Applique 1.3 0/F +0.0 / -1.0
		Parallel within 0.7
18	Taillamp to Body Side	0.9 +/- 0.8	-
19	Taillamp to Fascia	1.6 +/- 1.0	-
		Except 1.0 @ extreme outer	-
20	Liftgate to Fascia	4.8+/- 1.2	-
		Parallel within 1.5 Except 4.0 @ extreme sides	-
21	Light Bar to Liftgate	0.0+/- 0.5	-