Diagnostic Test

ACTIVE DTC
1. Turn the ignition on.
2. With the scan tool, read DTCs.
  Does the scan tool display this DTC as active?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK THE (F342) FUSED ASD RELAY OUTPUT CIRCUIT FOR AN OPEN
1. Turn the ignition off.
2. Disconnect the Fuel Injector 4 harness connector.
3. Turn the ignition on, engine not running.
4. With the scan tool, actuate the Auto Shutdown (ASD) Relay Control State.
5. Using a 12-volt test light connected to ground, check the (F342) Fused ASD Relay Output circuit in the Fuel Injector 4 harness connector.
  NOTE:
  The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.
  
  Is the test light illuminated and bright?
  
  Yes
  - Go To 3
  No
  - Repair the (F342) Fused ASD Relay Output circuit for an open.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK THE (K14) FUEL INJECTION 4 SIGNAL CIRCUIT FOR A SHORT TO BATTERY VOLTAGE
1. Turn the ignition off.
2. Disconnect the PCM C2 harness connector.
3. Turn the ignition on, engine not running.
4. With the scan tool, actuate the Auto Shutdown (ASD) Relay Control State.
5. Measure the voltage of the (K14) Fuel Injection 4 Signal circuit between ground and the Fuel Injector 4 harness connector.
  Is the voltage above 1.0 volt?
  
  Yes
  - Repair the (K14) Fuel Injection 4 Signal circuit for a short to battery voltage.
  - Perform POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
CHECK THE (K14) FUEL INJECTION 4 SIGNAL CIRCUIT FOR A SHORT TO THE (F342) FUSED ASD RELAY OUTPUT CIRCUIT
1. Turn the ignition off.
2. Measure the resistance between the (K14) Fuel Injection 4 Signal circuit and the (F342) Fused ASD Relay Output circuit in the Fuel Injector 4 harness connector.
  Is the resistance above 10k Ohms?
  
  Yes
  - Go To 5
  No
  - Repair the (K14) Fuel Injection 4 Signal circuit for a short to the (F342) Fused ASD Relay Output circuit.
  - Perform POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

CHECK THE FUEL INJECTOR

Measure the resistance of the Fuel Injector.

NOTE:

The resistance of the circuit will vary according to the temperature of the injector coil. Use the table below to determine the resistance range of the injector.

Fuel Injector Coil Resistance Based on Engine Temperature
Temperature	Resistance
-20° C (-4° F)	10 Ohms (+/-.6 of an Ohm)
20° C (68° F)	12 Ohms (+/-.6 of an Ohm)
60° C (140° F)	14 Ohms (+/-.6 of an Ohm)
100° C (212° F)	16 Ohms (+/-.6 of an Ohm)

Is the resistance of the Fuel Injector within the specified range?

Yes

Go To 6

Replace Fuel Injector 4 in accordance with the service information. Refer to INJECTOR(S), FUEL, REMOVAL .
Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

POWERTRAIN CONTROL MODULE (PCM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Fuel Injector 4 and the Powertrain Control Module.
2. Look for any chafed, pierced, pinched, or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals.
4. Perform any Technical Service Bulletins that may apply.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Replace and program the Powertrain Control Module (PCM) in accordance with the service information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .