Diagnostic Test

CHECK FOR AN ACTIVE DTC
NOTE:
This DTC must be active for the results of this test to be valid.
1. Perform any Service Bulletins that may apply.
2. Turn the ignition on.
3. For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
4. With the scan tool, read DTCs and record on the repair order.
5. With the scan tool, erase all DTCs.
6. Turn the ignition off for a minimum of 10.0 seconds.
7. Turn the ignition on.
8. With the scan tool, read ABS DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform ABS INTERMITTENT CONDITION diagnostic procedure. Refer to ABS INTERMITTENT CONDITION .
CHECK FOR POWERTRAIN CONTROL MODULE (PCM) DTCS
1. Refer to the recorded DTCs.
  Are there any PCM DTCs active or pending?
  
  Yes
  - Perform the applicable diagnostic procedure(s). Refer to 3.6L - DIAGNOSTIC CODE INDEX .
  No
  - Go To 3
WRONG VIN PROGRAMMED IN PCM
1. Turn the ignition on.
2. With the scan tool, read the VIN in the PCM.
3. Compare VIN in the PCM to the vehicle VIN.
  Is the correct VIN programmed in the PCM?
  
  Yes
  - Go To 4
  No
  - Program the correct VIN into the PCM. Follow the VIN programing procedure in the PCM/ECM reprogramming procedure. Refer to STANDARD PROCEDURE .
  - Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
INITIALIZE ABS MODULE
1. Perform any Service Bulletins that may apply.
  NOTE:
  When performing the ABS Initialization routine, the vehicle temperature must be above 10°C (50°F).
2. With the scan tool, under "Miscellaneous Functions" perform the ABS Initialization routine.
3. Turn the ignition off.
4. Cycle the ignition from off to on.
5. Wait ten seconds.
6. With the scan tool, read DTCs.
  Does the DTC remain active?
  
  Yes
  - Go To 5
  No
  - Test complete, the condition or conditions that originally set this DTC are not present at this time.
CHECK RELATED HARNESS CONNECTIONS
1. Turn the ignition off.
2. Disconnect the ABS Module harness connector.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
6. Connect the ABS Module harness connector. Be certain that the harness connector is fully seated and the connector lock is fully engaged.
7. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Connect the related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
  WARNING:
  To avoid personal injury or death, check brake capability is available before road testing.
10. Using the recorded Event and Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
11. With the scan tool, read ABS Module DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Anti-lock Brake System (ABS) Module in accordance with the Service Information. Refer to MODULE, ANTI-LOCK BRAKE SYSTEM (ABS), REMOVAL .
  - Perform ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  No
  - The wiring or poor connection problem has been repaired.
  - Perform ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .