Diagnostic Test

CHECK FOR ANY SERVICE BULLETINS OR MODULE SOFTWARE UPDATES
1. Check for any applicable Service Bulletins or Flash updates related to the DTC.
  Are there any applicable Service Bulletins or Flash updates?
  
  Yes
  - Perform the applicable repair.
  - Perform the ADAPTIVE CRUISE CONTROL VERIFICATION TEST. Refer to ADAPTIVE CRUISE CONTROL (ACC) VERIFICATION TEST .
  No
  - Go To 2
READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. For future reference, run and save a vehicle Scan Report and all related recorded data.
3. With the scan tool, erase all DTCs.
4. Turn the ignition off for a minimum of 10.0 seconds.
5. Turn the ignition on.
6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
7. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 3
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK TIRE SIZE AND CONFIGURATION
1. Verify that the tire size is correct and configured properly for the vehicle using the appropriate service information.
  Is the size for all tires on the vehicle correct and configured properly?
  
  Yes
  - Go To 4
  No
  - Repair as necessary.
  - Perform the ADAPTIVE CRUISE CONTROL VERIFICATION TEST. Refer to ADAPTIVE CRUISE CONTROL (ACC) VERIFICATION TEST .
CHECK FOR ANTI LOCK BRAKE SYSTEM (ABS) MODULE DTCS
1. Refer to the recorded DTCs.
  Are there any ABS DTCs present?
  
  Yes
  - Perform the applicable diagnostic procedure(s). Refer to ANTILOCK BRAKE SYSTEM (ABS) - DIAGNOSTIC CODE INDEX.
  No
  - Go To 5
CHECK RELATED ACC AND COMPONENT CONNECTIONS
1. Turn the ignition off.
2. Disconnect all ACC harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all ACC harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
11. With the scan tool, read ACC DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Adaptive Cruise Control (ACC) Module in accordance with the Service Information. Refer to MODULE, ADAPTIVE CRUISE CONTROL (ACC), REMOVAL .
  - Perform the ADAPTIVE CRUISE CONTROL VERIFICATION TEST. Refer to ADAPTIVE CRUISE CONTROL (ACC) VERIFICATION TEST .
  No
  - The wiring or poor connection has been repaired.
  - Perform the ADAPTIVE CRUISE CONTROL VERIFICATION TEST. Refer to ADAPTIVE CRUISE CONTROL (ACC) VERIFICATION TEST .