Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read Body Control Module (BCM) DTCs and record on the repair order.
2. Record the Environmental Data.
3. With the scan tool, erase DTCs.
4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR INTERMITTENT CONDITIONS procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK FOR ADDITIONAL LIN BUS DTCS
1. With the scan tool, read BCM DTCs.
  Is there any LIN BUS SIGNAL/MESSAGE FAILURE DTCs Active in the BCM?
  
  Yes
  - Go to and perform the appropriate diagnostic procedure.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 3
CHECK THE RIGHT REAR STEERING WHEEL SWITCH FOR PROPER OPERATION
1. Turn the ignition off.
2. Check the Right Rear Steering Wheel Switch for proper operation. Refer to DIAGNOSIS AND TESTING .
  Were any problems found with Right Rear Steering Wheel Switch?
  
  Yes
  - Replace the Right Rear Steering Wheel Switch in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 4
MEASURE THE VOLTAGE ON THE (D404) LIN BUS 4 CIRCUIT
1. Turn the ignition off.
2. If needed, disconnect the Right Rear Steering Wheel Switch harness connector.
3. Turn the ignition on.
4. Measure the voltage on the (D404) LIN Bus 4 circuit at the Right Rear Steering Wheel Switch harness connector.
  Is there any voltage present?
  
  Yes
  - Go To 7
  No
  - Go To 5
CHECK THE (D404) LIN BUS 4 CIRCUIT FOR AN OPEN
1. Turn the ignition off.
2. Disconnect the BCM C8/H harness connector.
3. Measure the resistance of the (D404) LIN Bus 4 circuit between the BCM C8/H harness connector and the Right Rear Steering Wheel Switch harness connector.
  Is the resistance above 3.0 Ohms?
  
  Yes
  - Repair the open in the (D404) LIN Bus 4 circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 6
CHECK THE (D404) LIN BUS 4 CIRCUIT FOR A SHORT TO GROUND
1. Check for continuity between ground and the (D404) LIN Bus 4 circuit at the Right Rear Steering Wheel Switch harness connector.
  Is there continuity between ground and the (D404) LIN Bus 4 circuit?
  
  Yes
  - Repair the short to ground in the (D404) LIN Bus 4 circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 7
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all BCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all BCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Body Control Module (BCM) in accordance with the Service Information. Refer to MODULE, BODY CONTROL (BCM), REMOVAL .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.