Diagnostic Test

CHECK FOR AN ACTIVE DTC
NOTE:
This DTC must be active for the results of this test to be valid.
1. Perform any Service Bulletins that may apply.
2. Turn the ignition on.
3. For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
4. With the scan tool, read DTCs and record on the repair order.
5. With the scan tool, erase all DTCs.
6. Turn the ignition off for a minimum of 10.0 seconds.
7. Turn the ignition on.
8. With the scan tool, read ABS DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the ABS-INTERMITTENT CONDITION TEST. Refer to ABS INTERMITTENT CONDITION .
PERFORM THE EXIT LOGISTIC MODE ROUTINE IN THE BODY CONTROL MODULE (BCM) AND TEST FOR DTCS
1. With the scan tool, under the BCM go to "Miscellaneous Functions" and perform the Exit Logistic Mode routine.
2. Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
3. With the scan tool, read ABS DTCs.
  Did the DTC return?
  
  Yes
  - Perform the Exit Logistic Mode routine again, if still unsuccessful.
  - Go To 3
  No
  - Test complete.
CHECK RELATED HARNESS CONNECTIONS
1. Turn the ignition off.
2. Disconnect the Body Control Module (BCM) harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
6. Connect the BCM harness connectors. Be certain that the harness connectors are fully seated and the connector lock is fully engaged.
7. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Connect the related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
  WARNING:
  To avoid personal injury or death, check brake capability is available before road testing.
10. Using the recorded Event and Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
11. With the scan tool, read ABS Module DTCs.
  Did the DTC return?
  
  Yes
  - Go To
    Refer to 4.
  No
  - Replace the Body Control Module (BCM) in accordance with the Service Information. Refer to MODULE, BODY CONTROL (BCM), REMOVAL .
  - Perform BCM VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Turn the ignition off.
2. Disconnect the ABS Module harness connector.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
6. Connect the ABS Module harness connector. Be certain that the harness connector is fully seated and the connector lock is fully engaged.
7. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Connect the related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
  WARNING:
  To avoid personal injury or death, check brake capability is available before road testing.
10. Using the recorded Event and Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
11. With the scan tool, read ABS Module DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Anti-lock Brake System (ABS) Module in accordance with the Service Information. Refer to MODULE, ANTI-LOCK BRAKE SYSTEM (ABS), REMOVAL .
  - Perform ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  No
  - The wiring or poor connection problem has been repaired.
  - Perform ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .