Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

Check The Cooling System For Proper Level And Condition
1. Check The Cooling System To Make Sure That The Coolant Is In Good Condition, At The Proper Level, And Meets Oem Specifications. Refer To Diagnosis And Testing .
  Is The Coolant Level And Condition Ok?
  
  Yes
  - Go To 2
  No
  - Inspect The Vehicle For A Coolant Leak And Add The Necessary Amount Of Coolant. Refer To SPECIFICATIONS
  - Perform The Powertrain Verification Test. Refer To POWERTRAIN VERIFICATION TEST .
Check For An Active Dtc
1. Start The Engine.
2. Allow The Engine To Reach Normal Operating Temperature.
3. Test Drive The Vehicle Under The Conditions In Which The Fault Originally Set By Reviewing The Freeze Frame Data.
4. With The Scan Tool, Read Dtcs And Record On The Repair Order.
  Is The Dtc Active Or Pending?
  
  Yes
  - Go To 3
  No
  - Perform The Intermittent Condition Diagnostic Procedure. Refer To INTERMITTENT CONDITION .
Check For Other Dtcs
1. Refer To The Recorded Dtcs.
  Are There Any Other Dtcs Active Or Pending?
  
  Yes
  - Perform The Applicable Diagnostic Procedure(s). Refer To 3.6L - DIAGNOSTIC CODE INDEX .
  No
  - Go To 4
Check The Egr System And Plumbing For A Leak
1. Visually Inspect The Egr System For A Leak Between The Egr Cooler And The Egr Valve For Signs Of A Leak (I.E. Loose Connections Or Damaged Plumbing.
  Were Any Problems Found?
  
  Yes
  - Perform The Appropriate Repair.
  - Perform The Powertrain Verification Test. Refer To POWERTRAIN VERIFICATION TEST .
  No
  - Go To 5
Check Cooling System For Proper Operation
1. Check The Following Cooling System Components:
  - Verify Condition And Operation Of The Accessory Belt And Tensioner.
  - Verify Proper Airflow Through The Radiator.
  - Verify That The Thermostat Is Opening Correctly.
  - Verify The Correct Coolant Flow Throughout The System.
  - During Engine Warm-Up, Monitor The Coolant Temperature And The Operation Of The Cooling Fan.
  Is The Cooling System Operating Correctly?
  
  Yes
  - Go To 6
  No
  - Perform The Appropriate Repairs.
  - Perform The Powertrain Verification Test. Refer To POWERTRAIN VERIFICATION TEST .
Check The Fuel Delivery System For Proper Operation
1. Perform The Checking The Fuel Delivery System Test Procedure. Refer To CHECKING THE FUEL DELIVERY SYSTEM (HARD START)
  Were Any Problems Found With The Fuel System?
  
  Yes
  - Perform The Appropriate Repair.
  - Perform The Powertrain Verification Test. Refer To POWERTRAIN VERIFICATION TEST .
  No
  - Go To 7
Check The Engine For A Mechanical Condition
1. Turn The Ignition Off.
2. Check For Any Of The Following Conditions/Mechanical Problems:
  - Air Intake System - Must Be Free From Leaks.
  - Engine Vacuum - Check The Engine For Vacuum Leaks.
  - Engine Valve Timing - Must Be Within Specifications.
  - Power Brake Booster - No Internal Vacuum Leaks.
  - Fuel - Must Be Free Of Contamination.
  - Fuel Injector - Plugged Or Restricted Injector; Control Wire Not Connected To Correct Injector.
  Are There Any Engine Mechanical Problems?
  
  Yes
  - Repair As Necessary.
  - Perform The Powertrain Verification Test. Refer To POWERTRAIN VERIFICATION TEST .
  No
  - Replace The Egr Temperature Sensor In Accordance With The Service Information.
  - Perform The Powertrain Verification Test. Refer To POWERTRAIN VERIFICATION TEST .