Diagnostic Test

WARNING: This page is about a different car, the 2016 Dodge Durango. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR CHECK FOR AN ACTIVE DTC
1. Turn the ignition on and test drive the vehicle with ESS enabled.
2. With the scan tool, read DTCs and record on the repair order.
  Is the DTC active or pending?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT DTC diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK THE (K806) ENGINE HOOD SWITCH 2 SIGNAL CIRCUIT FOR AN OPEN
1. Turn the ignition off.
2. Disconnect the Engine Hood Switch 2 harness connector.
3. Disconnect the PCM C1 harness connector.
4. Measure the resistance of the (K806) Engine Hood Switch 2 Signal circuit between the Engine Hood Switch 2 harness connector and the PCM C1 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 3
  No
  - Repair the (K806) Engine Hood Switch 2 Signal circuit for an open or high resistance.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK THE (Z909) SENSOR GROUND CIRCUIT FOR AN OPEN
1. Measure the resistance of the (Z909) Sensor Ground circuit between the Engine Hood Switch 2 harness connector and the PCM C1 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 4
  No
  - Repair the (Z909) Sensor Ground circuit for an open or high resistance.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK THE ENGINE HOOD SWITCH 2
1. Connect a jumper between the (K806) Engine Hood Switch 2 Signal circuit and the (Z909) Sensor Ground circuit at the Engine Hood Switch 2 harness connector.
2. Turn the ignition on.
3. With the scan tool, read DTCs.
  NOTE:
  The P152D-ENGINE HOOD SWITCH 2 CIRCUIT LOW DTC should display as active or pending with the jumper in place.
  
  Does the scan tool display as described above?
  
  Yes
  - Replace Engine Hood Switch 2.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 5
CHECK RELATED PCM AND COMPONENT CONNECTIONS
1. Perform any Service Bulletins that apply.
2. Disconnect all PCM harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
11. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Powertrain Control Module in accordance with the Service information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  - Test complete.