Diagnostic Test
- CHECK FOR AN ACTIVE DTC NOTE:
Make sure that the engine oil is at the proper level. Also, check the customers oil change history to ensure that the oil is being changed at the correct intervals and that the proper oil viscosity is being used.
- Start the engine and allow it to reach normal operating temperature.WARNING:
When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in possible serious or fatal injury.
- With the scan tool, read DTCs and record on the repair order.
Is the DTC active or pending?
Yes
- Go To 2
No
- Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
- Start the engine and allow it to reach normal operating temperature.
- ENGINE OIL/ENGINE MECHANICAL NOTE:
For the MDS to enable the 4 cylinder mode, the oil pressure has to be approximately 25 psi.
For the MDS to remain enabled in the 4 cylinder mode the engine oil pressure can not drop below 23.2 psi.
When checking the engine oil pressure use a mechanical gauge.
The following items must be considered before determining the cause of this DTC. Failure to do so may lead to misdiagnosis:
- ENGINE MECHANICAL TOLERANCES OUT OF SPECIFICATION
- ENGINE OIL PRESSURE OUT OF SPECIFICATION
- LOW ENGINE OIL
- DETERIORATED OR DIRTY OIL
- CORRECT ENGINE OIL VISCOSITY
- ENGINE OIL CONTAMINATED (i.e., coolant and/or fuel)
- If any of the above conditions are found, repair as necessary.
Were any of the above conditions present?
Yes
- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
No
- Go To 3
- ENGINE OIL PRESSURE SENSOR
- Replace the Engine Oil Pressure Sensor in accordance with the Service Information.
- Turn the ignition on.
- With the scan tool, erase DTCs in the PCM.
- Start the engine and test drive the vehicle. Make sure to drive the vehicle with the engine speed above 1150 rpm.
- With the scan tool, read DTCs.
Is the DTC active or pending?
Yes
- Go To 4
No
- Repair complete.
- Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
- CHECK RELATED PCM AND COMPONENT CONNECTIONS
- Perform any Service Bulletins that apply.
- Disconnect all PCM harness connectors.
- Disconnect all related in-line harness connections (if equipped).
- Disconnect the related component harness connectors.
- Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
- Proper connector installation.
- Damaged connector locks.
- Corrosion.
- Other signs of water intrusion.
- Weather seal damage (if equipped).
- Bent terminals.
- Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
- Terminals that have been pushed back into the connector cavity.
- Check for spread terminals and verify proper terminal tension.
Repair any conditions that are found.
- Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
- Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
- Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
- With the scan tool, erase DTCs.
- Test drive or operate the vehicle in accordance with the when monitored and set conditions.
- With the scan tool, read DTCs.
Did the DTC return?
Yes
- Replace the Powertrain Control Module in accordance with the Service information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL .
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
No
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
- Test complete.