Diagnostic Test

WARNING: This page is about a different car, the 2016 Dodge Durango. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR AN ACTIVE DTC
1. Diagnose and repair any other active component or circuit DTCs before continuing with this procedure.
2. Turn the ignition on.
3. With the scan tool, read DTCs and record on the repair order.
4. Start the engine and allow it to reach operating temperature.
  WARNING:
  When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in possible serious or fatal injury.
  
  NOTE:
  Attempt to operate the vehicle under conditions similar to which the DTC was set.
  
  NOTE:
  It may be necessary to test drive the vehicle within the DTC monitoring conditions in order for this DTC to set.
5. With the scan tool, read DTCs.
  Is the DTC active or pending?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
DIAGNOSTIC INSPECTION
NOTE:
Anything that affects the speed of the crankshaft can cause this DTC to set. When a misfire is detected, the PCM will shut down the injector control circuit for the misfiring cylinder. Misfire may occur and may not be caused by component failure. Any of the following conditions can cause a misfire.
1. Inspect the engine for any of the following conditions:
  - Worn serpentine belt
  - Misalignment or binding water pump, P/S Pump or A/C Compressor pulleys
  - Improper CKP, CMP, or MAP Sensor mounting.
  - Poor connector/terminal to component connection for CKP Sensor, CMP Sensor, MAP Sensor, Throttle Body, Fuel Injector, Ignition Coil, etc.
  - Corroded PCM power or ground circuits.
  - Vacuum leaks.
  - Restriction in the air induction or exhaust system.
  - Internal engine component malfunction.
  - Moisture on ignition system components
  - Insufficient fuel
  - Low quality fuel
  - Manual transmission bog
  - Towing overload
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 3
CHECK THE FUEL DELIVERY SYSTEM
1. Perform the diagnostic procedures for FUEL PRESSURE LEAK DOWN and FUEL DELIVERY SYSTEM OUTPUT - FLOW TEST. Refer to CHECKING THE FUEL DELIVERY SYSTEM (HARD START) .
  Were any problems found?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
CHECK THE IGNITION COIL OPERATION
1. Perform the diagnostic procedure for CHECKING THE IGNITION COIL OPERATION. Refer to CHECKING THE IGNITION COIL PERFORMANCE .
  Were any problems found?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 5
CHECK THE MAP SENSOR OPERATION
1. Perform the diagnostic procedure for CHECKING THE MAP SENSOR OPERATION. Refer to CHECKING THE MAP SENSOR PERFORMANCE .
  Were any problems found?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 6
CHECK THE OXYGEN SENSOR OPERATION
1. Perform the diagnostic procedure for CHECKING THE OXYGEN SENSOR OPERATION. Refer to CHECKING THE OXYGEN SENSOR PERFORMANCE .
  Were any problems found?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 7
CHECK THE ENGINE MECHANICAL SYSTEM
1. Perform the diagnostic procedure for CHECKING THE ENGINE MECHANICAL SYSTEM. Refer to DIAGNOSIS AND TESTING .
  Were any problems found?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 8
CHECK RELATED PCM AND COMPONENT CONNECTIONS
1. Perform any Service Bulletins that apply.
2. Disconnect all PCM harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
11. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Powertrain Control Module in accordance with the Service information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  - Test complete.