LEMON Manuals: Even more car manuals for everyone
Home >> Dodge and Ram >> 2015 >> Durango SXT, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 168 (Occupant Restraint Controller (Orc) - DTCS B0001-11 To B0052-95) >> DTC Troubleshooting >> B0028-13-1ST Row Right Thorax/Seat Mounted Side Squib 1 - Circuit Open >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2016 Dodge Durango. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FOR AN ACTIVE DTC 
    1. With the scan tool, read ORC DTCs and record on the repair order.
    2. Record the Environmental Data.
    3. With the scan tool, erase DTCs.
    4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
    5. With the scan tool, read ORC DTCs.

      Did the DTC return?

      Yes 

      • Go To  2

      No 

      • Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. Refer to RESTRAINTS SYSTEM INTERMITTENT TEST .
      • Probing of the circuit cavities at the ORC Module body harness connectors or vehicle connectors is only to be done with a approved test lead from the test lead 10159-6 or the use of Breakout Box 8443-55 to prevent vehicle wiring harness connector damage during diagnostic procedures. 
  2. CHECK FOR OPEN SQUIB CIRCUITS IN RIGHT SEAT AIRBAG 
    WARNING:

    Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    1. Disconnect the Right Seat Airbag harness connector.
      WARNING:

      Do not place an intact non-deployed Seat Squib Airbag face down on a hard surface, the airbag will propel into the air if accidentally deployed. Failure to follow these instructions may result in possible serious or fatal injury.

      NOTE:

      Check the connectors - Clean and repair as necessary.

    2. Connect the (special tool #8443A, SRS Load Tool) and the (special tool #8443-8, Jumper, SRS Load) to the Right Seat Airbag harness connector.
    3. If the vehicle is equipped with the standard key ignition, follow this ignition on warning.
      WARNING:

      Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    4. If the vehicle is equipped with the keyless ignition, follow this ignition on warning.
      WARNING:

      Disconnect the 12-volt battery wait two minutes before proceeding, remove the ORC fuses, connect the 12-volt battery, wait two minutes before proceeding. Cycle the ignition to the On position, then reconnect the ORC fuses. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    5. With the scan tool, read the active ORC DTC.

      Does the scan tool display: B0028-13-1ST ROW RIGHT SEAT MOUNTED SIDE SQUIB 1 - CIRCUIT OPEN?

      Yes 

      • Go To  3

      No 

      WARNING:

      Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

  3. CHECK FOR OPEN RIGHT SEAT AIRBAG SQUIB CIRCUIT IN THE SEAT BACK 
    WARNING:

    Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    1. Disconnect the Right Seat Airbag appropriate connector (under Right Seat).
      NOTE:

      Check the connectors - Clean and repair as necessary.

    2. Connect the (special tool #8443A, SRS Load Tool) and the appropriate SRS Load Tool Jumper to the appropriate Right Seat Airbag harness connector.
    3. If the vehicle is equipped with the standard key ignition, follow this ignition on warning.
      WARNING:

      Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    4. If the vehicle is equipped with the keyless ignition, follow this ignition on warning.
      WARNING:

      Disconnect the 12-volt battery wait two minutes before proceeding, remove the ORC fuses, connect the 12-volt battery, wait two minutes before proceeding. Cycle the ignition to the On position, then reconnect the ORC fuses. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    5. With the scan tool, read the active ORC DTC.

      Does the scan tool display: B0028-13-1ST ROW RIGHT SEAT MOUNTED SIDE SQUIB 1 - CIRCUIT OPEN?

      Yes 

      • Go To  4

      No 

      WARNING:

      Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

      • In accordance with the Service Information repair or replace the Right Seat Airbag wiring harness (Side Airbag Jumper). Open Right Seat Airbag circuits between the C323 connector and the Right Seat Airbag connector.
      • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .
  4. CHECK (R8) RIGHT SEAT SQUIB 1 LINE 1 CIRCUIT FOR AN OPEN 
    WARNING:

    Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    1. Disconnect the (special tool #8443A, SRS Load Tool) and the (special tool #8443-8, Jumper, SRS Load) from the Right Seat Airbag harness connector.
    2. Disconnect the ORC harness connectors.
      NOTE:

      Check the connectors - Clean and repair as necessary.

    3. Connect the test leads to the DVOM.
    4. Measure the resistance of the (R8) Right Seat Squib 1 Line 1 circuit between the Right Seat Airbag connector terminal 2 and the ORC module body harness connector terminal C1-B 89.

      Is the resistance below 1.0 Ohm?

      Yes 

      • Go To  5

      No 

      • In accordance with the Service Information repair or replace the Right Seat Airbag body wiring harness.
      • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .
  5. CHECK (R6) RIGHT SEAT SQUIB 1 LINE 2 CIRCUIT FOR AN OPEN 
    1. Measure the resistance of the (R6) Right Seat Squib 1 Line 2 circuit between the Right Seat Squib 1 Airbag connector terminal 1 and the ORC module body harness connector terminal C1-B 90.

      Is the resistance below 1.0 Ohm?

      Yes 

      WARNING:

      If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment. Failure to follow these instructions may result in possible serious or fatal injury.

      No 

      • In accordance with the Service Information repair or replace the Right Seat Airbag body wiring harness.
      • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .
scientia non olet · About LEMON Manuals