LEMON Manuals: Even more car manuals for everyone
Home >> Dodge and Ram >> 2009 >> Durango 4WD V8-4.7L >> Repair and Diagnosis >> Restraints and Safety Systems >> Seat Belt Systems >> Seat Belt Retractor >> Service and Repair >> Seat Belt Retractor - Removal >> Front

Front






FRONT

WARNING: To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable. Wait two minutes for the system capacitor to discharge before performing further diagnosis or service. On vehicles equipped with the optional Hybrid Electric Vehicle (HEV) system, a technician trained in proper HEV service safety procedures must also remove the high voltage service disconnect from the high voltage battery pack. This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental airbag deployment. Failure to follow these instructions may result in possible serious or fatal injury.

WARNING: To avoid serious or fatal injury during and following any seat belt or child restraint anchor service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or ineffective buckle or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to repair a seat belt or child restraint component. Always replace damaged or ineffective seat belt and child restraint components with the correct, new and unused replacement parts listed in the Chrysler Mopar (R) Parts Catalog. Failure to follow these instructions may result in possible serious or fatal injury.

NOTE: The following procedure is for replacement of an ineffective or damaged seat belt and retractor unit. The front retractor also includes a seat belt tensioner. If the front seat belt or retractor is ineffective or damaged, but the seat belt tensioner is not deployed, review the recommended procedures for handling non-deployed supplemental restraints. Service and Repair . If the seat belt tensioner has been deployed, review the recommended procedures for service after a supplemental restraint deployment before removing the unit from the vehicle. Service and Repair .





1. Adjust the front seat to its most forward position for easiest access to the front seat belt lower anchor and the B-pillar trim.
2. Disconnect and isolate the battery negative cable. On vehicles equipped with the optional Hybrid Electric Vehicle (HEV) system, a technician trained in proper HEV service safety procedures must also remove the high voltage service disconnect from the high voltage battery pack. Wait two minutes for the system capacitors to discharge before further service.
3. Using a trim stick or another suitable wide flat-bladed tool, gently pry the seat belt anchor cover (2) to remove it from the rear of the outboard seat side shield (1).





4. Remove the screw (2) that secures the lower anchor (3) to the bracket on the outboard side of the front seat cushion frame.





5. Unsnap the upper edge of the trim cover (3) from the front seat belt turning loop (1) and disengage the tab (2) on the lower edge of the cover to access the turning loop screw.





6. Remove the screw (4) that secures the seat belt turning loop (5) to the height adjuster (2) on the upper B-pillar.
7. Remove the seat belt turning loop from the height adjuster.
8. Remove the upper trim (1) from the inside of the B-pillar. B-Pillar Trim Panel-Removal.





9. Remove the lower trim (2) from the inside of the B-pillar (4). B-Pillar Trim Panel-Removal.
10. Remove the screw (3) that secures the belt web guide (1) to the B-pillar.
11. Disconnect the body wire harness connector (5) from the seat belt tensioner initiator on the retractor (7).
12. Disconnect the second body wire harness connector from the seat belt switch connector receptacle on the retractor.
13. Remove the screw (8) that secures the upper retractor bracket to the B-pillar.
14. Remove the screw (6) that secures the lower retractor bracket to the B-pillar.
15. Disengage the engagement tab on the upper retractor bracket from the engagement slot in the B-pillar.
16. Remove the front seat belt and retractor from the B-pillar as a unit.

scientia non olet · About LEMON Manuals