LEMON Manuals: Even more car manuals for everyone
Home >> Dodge and Ram >> 2003 >> Durango Base, 5.9 Z, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 105 (Body Diagnostic Procedures) >> Diagnostic Information And Procedure >> Airbag >> Symptom: Passenger Seat Belt TENSIONER Circuit Shorted >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2004 Dodge Dakota. However, it is still accessible from the selected car via links, so may be relevant.
PASSENGER SEAT BELT TENSIONER CIRCUIT SHORTED - DIAGNOSTIC PROCEDURE

TEST ACTION
1 Turn the ignition on.
Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be referred to as an ACM.

SELECT ACTIVE or STORED DTC:
  1. ACM - ACTIVE DTC
    1. Go To 2
  2. ACM - STORED DTC
    1. Go To 4
NOTE: When reconnecting Airbag system components, the ignition must be turned off and the battery must be disconnected.
2
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Passenger Seat Belt Tensioner connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Passenger Seat Belt Tensioner connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIII(R), read the active DTC's.Does the DRBIII(R) show PASSENGER SEAT BELT TENSIONER CIRCUIT SHORT?
  1. Yes --> Go To 3
  2. No --> Replace the Passenger Seat Belt Tensioner in accordance with the Service Information.

    Perform AIRBAG VERIFICATION TEST - VER 1  .
3
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool Adaptor to the Airbag Control Module connector.Disconnect the Load Tool from the Passenger Seat Belt Tensioner connector.Measure the resistance between the Passenger SBT Line 1 and line 2 circuit at the Passenger SBT connector.Is the resistance below 10K ohms?
  1. Yes --> Repair the Passenger SBT Line 1 circuit for a short to the Passenger SBT Line 2 circuit.

    Perform AIRBAG VERIFICATION TEST - VER 1  .

  2. No --> Replace the Airbag Control Module in accordance with the Service information.

    Perform AIRBAG VERIFICATION TEST - VER 1  .
4
NOTE: Ensure the battery is fully charged.
With the DRBIII(R), record and erase all DTCs from all modules.All active codes must be resolved before diagnosing any stored codes.Maintain a safe distance from all airbags while performing the following steps.With the DRBIII(R) monitor active codes as you work through the system.
NOTE: If equipped with Passenger Airbag On-Off switch, read the DTC's in all switch positions.
Wiggle the wiring harness and connectors of the appropriate airbag system and rotate the steering wheel from stop to stop.
NOTE: Check connectors - Clean and repair as necessary.
You have just attempted to simulate the condition that initially set the trouble code message.The following additional checks may assist you in identifying a possible intermittent problem:
  • Visually inspect related wire harness connectors. Look for broken, bent, pushed out, spread, corroded, or contaminated terminals.
  • Visually inspect the related harnesses. Look for chafed, pierced, pinched or partially broken wire.
  • Refer to SYSTEM WIRING DIAGRAMS and Technical Service Bulletins that may apply.
Did the DTC become active ?
  1. Yes --> Select appropriate symptom from Symptom List.
  2. No --> No problem found at this time. Erase all codes before returning vehicle to customer.
scientia non olet · About LEMON Manuals