Diagnostic Test

Read And Record DTCS And Environmental Data - Erase DTCS And Check For DTC To Return
1. With The Scan Tool, Read DTCS In All Electronic Control Units (ECUS) And Record On The Repair Order.
2. Note: The Radio Must Be On And A Front Door Must Remain Open Whenever Checking Or Erasing Radio DTCS.
3. With The Scan Tool, Run A Vehicle Scan Report, Or Record The Environmental Data Related To The DTCS.
4. With The Scan Tool, Erase All DTCS.
5. Turn The Ignition Off For A Minimum Of 10.0 Seconds.
6. Turn The Ignition On.
7. Using The Recorded Environmental Data And The When Monitored Conditions Above, Operate The Vehicle In The Conditions That Set The DTC.
8. With The Scan Tool, Read DTCS.
NOTE:
The Radio Must Be On And A Front Door Must Remain Open Whenever Checking Or Erasing Radio DTCS.

Did The DTC Return?

Yes
- Go To 2
No
- Perform The Appropriate Intermittent Condition Diagnostic Procedure. Refer To Testing For An Intermittent Condition .
Check The Related Anc Microphone
1. Ensure One Of The Front Doors Is Still Open.
2. With The Scan Tool, Erase The DTCS.
3. Turn The Ignition Off.
4. Disconnect The Related Anc Microphone Harness Connector.
5. Turn The Ignition On.
6. Turn The Radio On.
7. With The Scan Tool, Read The Radio DTCS.
  Did The DTC Return?
  
  Yes
  - Go To 3
  No
  - Replace The Related Anc Microphone In Accordance With The Service Information.
  - Perform The Body Verification Test. Refer To Body Verification Test .
Isolate And Check The Anc Microphone (+) Circuit For A Short To Ground
1. The Ignition Must Be Off When Checking A Circuit For Continuity To Ground.
2. Isolate The Circuit By Disconnecting The Electronic Control Unit (ECU) And Every Component Harness Connector Containing The Circuit Being Tested. Note: Use The Appropriate System Wiring Diagram As A Guide To Follow The Path Of The Circuit.
3. Connect The Negative Lead Of The DVOM To A Known Good Ground.
4. With The Positive Lead Of The DVOM, Probe The Circuit Being Tested At The Component Harness Connector And Check For Continuity Between The Circuit And Ground.
NOTE:
When Probing A Circuit At An Electronic Control Unit (ECU) Harness Connector, Always Use An Appropriate Back Probing Tool To Prevent Any Possible Damage To The ECU Terminals.

NOTE:
There Should Be No Continuity Between Ground And The Circuit Being Tested.

Is There Continuity Between Ground And The Circuit Being Tested?

Yes
- Repair The Circuit For A Short To Ground. Use The Appropriate System Wiring Diagram As A Guide To Trace The Circuit And Look For Any In-Line Connectors To Help Isolate The Location Of The Short.
- Perform The Body Verification Test. Refer To Body Verification Test .
No
- Go To 4
Isolate And Check The Anc Microphone (-) Circuit For A Short To Ground
1. The Ignition Must Be Off When Checking A Circuit For Continuity To Ground.
2. Isolate The Circuit By Disconnecting The Electronic Control Unit (ECU) And Every Component Harness Connector Containing The Circuit Being Tested. Note: Use The Appropriate System Wiring Diagram As A Guide To Follow The Path Of The Circuit.
3. Connect The Negative Lead Of The DVOM To A Known Good Ground.
4. With The Positive Lead Of The DVOM, Probe The Circuit Being Tested At The Component Harness Connector And Check For Continuity Between The Circuit And Ground.
NOTE:
When Probing A Circuit At An Electronic Control Unit (ECU) Harness Connector, Always Use An Appropriate Back Probing Tool To Prevent Any Possible Damage To The ECU Terminals.

NOTE:
There Should Be No Continuity Between Ground And The Circuit Being Tested.

Is There Continuity Between Ground And The Circuit Being Tested?

Yes
- Repair The Circuit For A Short To Ground. Use The Appropriate System Wiring Diagram As A Guide To Trace The Circuit And Look For Any In-Line Connectors To Help Isolate The Location Of The Short.
- Perform The Body Verification Test. Refer To Body Verification Test .
No
- Go To 5
Check Related Harness Connections
1. Disconnect All Radio Harness Connectors.
2. Disconnect All Related In-Line Harness Connections (If Equipped).
3. Disconnect The Related Component Harness Connectors.
4. Inspect Harness Connectors, Component Connectors, And All Male And Female Terminals For The Following Conditions:
  - Proper Connector Installation.
  - Damaged Connector Locks.
  - Corrosion.
  - Other Signs Of Water Intrusion.
  - Weather Seal Damage (If Equipped).
  - Bent Terminals.
  - Overheating Due To A Poor Connection (Terminal May Be Discolored Due To Excessive Current Draw).
  - Terminals That Have Been Pushed Back Into The Connector Cavity.
  - Perform A Terminal Drag Test On Each Connector Terminal To Verify Proper Terminal Tension.
  Repair Any Conditions That Are Found.
5. Reconnect All Radio Harness Connectors. Be Certain That All Harness Connectors Are Fully Seated And The Connector Locks Are Fully Engaged.
6. Reconnect All In-Line Harness Connectors (If Equipped). Be Certain That All Connectors Are Fully Seated And The Connector Locks Are Fully Engaged.
7. Reconnect All Related Component Harness Connectors. Be Certain That All Connectors Are Fully Seated And The Connector Locks Are Fully Engaged.
  NOTE:
  The Radio Must Be On And A Front Door Must Remain Open Whenever Checking Or Erasing Radio DTCS.
8. With The Scan Tool, Erase DTCS.
9. Using The Recorded Environmental Data, Along With The When Monitored And Set Conditions Above, Operate The Vehicle In The Conditions That Set The DTC.
10. With The Scan Tool, Read Radio DTCS.
  Did The DTC Return?
  
  Yes
  - Replace The Radio In Accordance With The Service Information. Refer To Module, Radio Receiver, Removal And Installation .
  - Perform The Body Verification Test. Refer To Body Verification Test .
  No
  - Perform The Body Verification Test. Refer To Body Verification Test .
  - Test Complete.