Diagnostic Test

WARNING: This page is about a different car, the 2015 RAM 3500 HD and 2015 RAM 2500 HD. However, it is still accessible from the selected car via links, so may be relevant.

DTC ACTIVE
1. Turn the ignition on.
2. With the scan tool, record all Freeze frame data.
3. With the scan tool, erase DTCs.
4. Turn the ignition off for 75 seconds.
5. Start the engine and let idle for one minute.
6. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION - 6.7L .
CHECK THE (K674) AIR INTAKE THROTTLE MOTOR (-) CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the EGR Airflow Control Valve harness connector.
3. Disconnect the PCM C1 harness connector.
4. Measure the resistance between ground and the (K674) Air Intake Throttle Motor (-) circuit at the EGR Airflow Control Valve harness connector.
  Is the resistance below 10k Ohms?
  
  Yes
  - Repair the (K674) Air Intake Throttle Motor (-) circuit for a short to ground.
  - Perform the POWERTRAIN VERIFICATION TEST - 6.7L. Refer to POWERTRAIN VERIFICATION TEST - 6.7L .
  No
  - Go To 3
CHECK THE (K673) AIR INTAKE THROTTLE MOTOR (+) CIRCUIT FOR A SHORT TO GROUND
1. Measure the resistance between ground and the (K673) Air Intake Throttle Motor (+) circuit at the EGR Airflow Control Valve harness connector.
  Is the resistance below 10k Ohms?
  
  Yes
  - Repair the (K673) Air Intake Throttle Motor (+) circuit for a short to ground.
  - Perform the POWERTRAIN VERIFICATION TEST - 6.7L. Refer to POWERTRAIN VERIFICATION TEST - 6.7L .
  No
  - Go To 4
EGR AIRFLOW CONTROL VALVE
1. Replace the EGR Airflow Control Valve in accordance with the Service Information. Refer to VALVE, EXHAUST GAS RECIRCULATION (EGR) AIRFLOW CONTROL, REMOVAL .
2. Reconnect the EGR Airflow Control Valve harness connector.
3. Reconnect the PCM C1 harness connector.
4. Turn the ignition on.
5. With the scan tool, erase DTCs.
6. Start the engine and allow it to idle for one minute.
7. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 5
  No
  - Repair complete.
  - Perform the POWERTRAIN VERIFICATION TEST - 6.7L. Refer to POWERTRAIN VERIFICATION TEST - 6.7L .
POWERTRAIN CONTROL MODULE
1. Disconnect all PCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Freeze Frame and Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read PCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Powertrain Control Module (PCM) in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL, 6.7L DIESEL, REMOVAL .
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST - 6.7L .
  No
  - Test complete.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST - 6.7L .