LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2011 >> 300 C, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 534 (3.0L Diesel (Service Information) 1500) >> Cylinder Head >> Cover(S), Cylinder Head >> Removal >> Right Bank

Right Bank

WARNING: This page is about a different car, the 2014 RAM 1500. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle. Refer to HOISTING, STANDARD PROCEDURE .
  3. Remove the lower engine oil dipstick bolt.
  4. Drain the cooling system. Refer to STANDARD PROCEDURE .
  5. Lower the vehicle.
    Fig 1: Removing/Installing Engine Cover
    GC0158138Courtesy of CHRYSLER GROUP, LLC
  6. Remove the engine cover (1).
  7. Disconnect the Charge Air Cooler (CAC) hose at resonator (3)
  8. Remove the CAC hose (2) from the turbocharger.
  9. Remove the generator. Refer to GENERATOR, REMOVAL .
  10. Remove nut and the engine oil dip stick.
    Fig 2: Right Exhaust Manifold Heat Shield & Bolts
    GC0146791Courtesy of CHRYSLER GROUP, LLC
  11. Remove bolts (1) and the right exhaust manifold heat shield (2).
    Fig 3: EGR Valve Wire Harness Connector
    GC0158070Courtesy of CHRYSLER GROUP, LLC
  12. Disconnect the EGR valve wire harness connector (1).
    Fig 4: EGR Cooler Vacuum Bypass Hose
    GC0146748Courtesy of CHRYSLER GROUP, LLC
  13. Disconnect the EGR cooler vacuum bypass hose (1).
  14. Remove the EGR tube. Refer to TUBE, EXHAUST GAS RECIRCULATION (EGR), REMOVAL .
    Fig 5: Turbocharger-To-EGR Cooler Tube Bolts
    GC0158212Courtesy of CHRYSLER GROUP, LLC
  15. Remove the turbocharger-to-EGR cooler tube bolts (1).
    Fig 6: EGR Cooler Coolant Tube & Bolts
    GC0146645Courtesy of CHRYSLER GROUP, LLC
  16. Remove bolts (1 and 3) and the EGR cooler coolant tube (2).
    Fig 7: EGR Cooler Supply Hose
    GC0146747Courtesy of CHRYSLER GROUP, LLC
  17. Disconnect the EGR cooler supply hose (1).
    Fig 8: EGR Cooler Bypass Valve Support Bracket & Bolts
    GC0158004Courtesy of CHRYSLER GROUP, LLC
  18. Loosen bolt (1) securing EGR cooler bypass valve support bracket (2).
  19. Remove bolt (3) at the rear EGR cooler bypass valve support bracket (2).
    Fig 9: Cooler Assembly Bracket & Bolts
    GC0146749Courtesy of CHRYSLER GROUP, LLC
  20. Remove bolts (2) and the EGR and cooler assembly bracket (1).
    Fig 10: Fuel Injector, Hold Down Bolt, Washer & Retaining Claw
    GC0146598Courtesy of CHRYSLER GROUP, LLC
  21. Remove the right side fuel injectors. Refer to INJECTOR(S), FUEL, REMOVAL .
    Fig 11: Turbocharger-To-EGR Supply Tube Heat Shield & Nuts
    GC0158000Courtesy of CHRYSLER GROUP, LLC
  22. Remove nuts (2) and the turbocharger-to-EGR supply tube heat shield (1).
    Fig 12: Cylinder Head Cover & Bolts
    GC0146717Courtesy of CHRYSLER GROUP, LLC
  23. Remove bolts (1) and the cylinder head cover (2).
scientia non olet · About LEMON Manuals