LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2011 >> 300 C, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 534 (3.0L Diesel (Service Information) 1500) >> Cylinder Head >> Cover(S), Cylinder Head >> Removal >> Left Bank

Left Bank

WARNING: This page is about a different car, the 2014 RAM 1500. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle. Refer to HOISTING, STANDARD PROCEDURE .
  3. Drain the cooling system. Refer to STANDARD PROCEDURE .
  4. Lower the vehicle.
    Fig 1: Removing/Installing Engine Cover
    GC0158138Courtesy of CHRYSLER GROUP, LLC
  5. Remove the engine cover (1).
  6. Disconnect the Charge Air Cooler (CAC) hose at resonator (3).
  7. Remove the CAC hose (2) from the turbocharger.
  8. Release clips (1) and remove the charge air resonator (3).
  9. Remove air cleaner body and intake air tube. Refer to BODY, AIR CLEANER, REMOVAL .
    Fig 2: High Pressure Pump Blocker Shield & Bolts
    GC0146780Courtesy of CHRYSLER GROUP, LLC
  10. Remove bolts (2) and the fuel injection pump blocker shield (1).
    Fig 3: Low Pressure Supply Line, Return Line & Clips
    GC0158152Courtesy of CHRYSLER GROUP, LLC
  11. Remove safety clips (3, 4) and disconnect the low pressure supply (5) and return (2) lines at manifold. Refer to FITTING, QUICK CONNECT .
  12. Remove bolt securing the coolant tube-to fuel line bracket.
  13. Remove nuts and the low pressure supply (2) and return (1) line bracket from cylinder head cover.
  14. Disconnect the brake booster vacuum hose.
  15. Disconnect the two heater hoses at bulk head.
    Fig 4: bolts, A/C Clutch Electrical Connector, A/C Compressor & Bracket
    GC0146793Courtesy of CHRYSLER GROUP, LLC
  16. Remove the serpentine belt. Refer to BELT, SERPENTINE, REMOVAL .
  17. Raise and support the vehicle.
    NOTE:

    Removal of the A/C compressor does not require the refrigerant to be evacuated.

  18. Remove the bolts (2 and 5) that secure the A/C compressor (6) to the A/C compressor bracket (7).
  19. Lower the vehicle.
  20. Disconnect the A/C clutch wire harness connector (1).
  21. Support the A/C compressor, remove the nut (4) and stud (3) that secures the A/C compressor to the bracket and position aside the compressor.
    Fig 5: Remove/Install Oil Cooler Assembly
    GC0158173Courtesy of CHRYSLER GROUP, LLC
  22. Remove the oil cooler assembly. Refer to ADAPTER, OIL COOLER, REMOVAL .
    Fig 6: Glow Plug Wire Harness Connector
    GC0146738Courtesy of CHRYSLER GROUP, LLC
  23. Disconnect glow plug wire harness connector (1).
    Fig 7: Camshaft Position Sensor, Connector & Bolt
    GC0146584Courtesy of CHRYSLER GROUP, LLC
  24. Disconnect the Camshaft Position (CMP) sensor wire harness connector (3).
    Fig 8: Fuel Injector, Hold Down Bolt, Washer & Retaining Claw
    GC0146595Courtesy of CHRYSLER GROUP, LLC
  25. Remove the fuel injectors. Refer to INJECTOR(S), FUEL, REMOVAL .
    Fig 9: Left Cylinder Head Cover & Bolts
    GC0146670Courtesy of CHRYSLER GROUP, LLC
  26. Loosen bolts (1) and remove the left cylinder head cover (2).
scientia non olet · About LEMON Manuals