Diagnostic Test

1. With the scan tool, read Occupant Restraint Controller (ORC) DTCs.

   Does the scan tool display any active DTCs relating to internal faults, ignition faults, or battery faults?

   Yes 

   • Diagnose and repair the DTCs. Refer to DIAGNOSTIC CODE INDEX for a complete list of diagnostic procedures.

   No 

   • Go To  2

Does the scan tool display active: B1B95-PASSENGER SEAT TRACK POSITION SENSOR CIRCUIT OPEN?

Yes 

• Go To  3

No 

• Perform the AIRBAG SYSTEM INTERMITTENT TEST. Refer to STANDARD PROCEDURE .

1. Using the wiring diagram/schematic as a guide, inspect the Passenger Seat Harness wiring and connectors. Look for chafed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or contaminated terminals.

   Are any of these conditions present?

   Yes 

   NOTE:

   Do not attempt to repair the Seat Harness. Replace the Seat Harness if any of these conditions exist

   • Replace the Passenger Seat Harness in accordance with the Service Information.
   • Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .

   No 

   • Go To  4

1. Verify that the Passenger Seat Harness is routed correctly.

   Is the Passenger Seat Harness routed correctly?

   Yes 

   • Go To  5

   No 

   • Reroute the Passenger Seat Harness as necessary.
   • Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .

Fig 1: Checking Passenger Seat Position Sensor Data And Voltage Circuit For An Open

Courtesy of CHRYSLER GROUP, LLC

1. Disconnect the ORC connectors.
2. Connect the (special tool #8443-25, 56 Way ACM Adapter) to the ORC C2 connector.
3. Measure the resistance of the (R262) Passenger Seat Position Sensor Data circuit between the (special tool #8443-25, 56 Way ACM Adapter) cavity 32-25 and the Passenger Seat Track Position Sensor connector cavity 1.
   Fig 2: Measuring Resistance Of Passenger Seat Position Sensor Voltage

   Courtesy of CHRYSLER GROUP, LLC
4. Measure the resistance of the (R264) Passenger Seat Position Sensor Voltage circuit between the (special tool #8443-25, 56 Way ACM Adapter) cavity 32-26 and the Passenger Seat Track Position Sensor connector cavity 2.

   Is the resistance of either circuit above 5.0 Ohms?

   Yes 

   NOTE:

   Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.

   • Replace the Passenger Seat Harness in accordance with the Service Information.
   • Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .

   No 

   • Go To  6

1. Replace the Passenger Seat Track Position Sensor.
2. Reconnect the vehicle body harness to the Seat Track Position Sensor.
3. Remove any special tools or jumper wires and reconnect all previously disconnected components - except the Battery.
   WARNING:

   Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

4. Connect the scan tool to the Data Link Connector - use the most current software available.
5. Use the scan tool and erase the stored codes in all airbag system modules.
6. Turn the Ignition Off, and wait 15 seconds before turning the Ignition On.
7. Wait one minute, and read active codes and if there are none present read the stored codes.

   Did the active Passenger Seat Track Position Sensor DTC return?

   Yes 

   WARNING:

   If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to follow these instructions may result in possible serious or fatal injury.

   WARNING:

   Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

   • Replace the Occupant Restraint Controller (ORC) in accordance with the service information.
   • Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .

   No 

   • Repair is complete.
   • Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .