LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2011 >> 300 C, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 425 (5.7L - DTCS P0205 To P058B - 2500 Hd & 3500 Hd) >> Diagnosis And Testing >> P0340-Camshaft Position Sensor Circuit - Bank 1 Sensor 1 >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2013 RAM 3500 HD and 2013 RAM 2500 HD. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FOR APPLICABLE TSB 
    1. Check for any applicable TSBs that may apply for this issue.

      Were there any applicable TSBs?

      Yes 

      • Perform the applicable TSB. Erase the DTC and perform the verification test.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Go To  2
  2. ACTIVE DTC 
    1. Turn the ignition on.
    2. Read and copy the DTCs and freeze frame data.
    3. Start the engine or crank the engine for at least ten seconds.
    4. With the scan tool, select View DTCs.

      Is the status Active for this DTC?

      Yes 

      • Go To  5

      No 

      • Go To  3
  3. WIRE HARNESS/CKP SENSOR INSPECTION 
    1. Turn the ignition off.
    2. Disconnect the harness connectors at the PCM and Cam Sensor and inspect for wire chaffing or rub conditions, terminals pushed out on the wiring connector, bent terminals at the PCM and Cam Sensor, water in the connector cavities, presence of corrosion on the terminals of the connectors or components.
    3. Visually inspect the mounting area of Cam Sensor for debris/damage or a loose sensor. Remove the Cam Sensor and inspect the end of the sensor for signs of damage or debris. Rotate the engine and if possible, inspect the target wheel for any signs of damage. Reinstall the Cam Sensor and ensure that the sensor is properly installed and torqued to proper specification.
      NOTE:

      Due to the fact that this DTC is set by an intermittent loss of the signal, the most likely cause is a poor connection at the Cam Sensor or PCM terminals, or a poor signal between the Cam Sensor and target wheel. Because of this, unplugging and reconnecting the harness connectors, or repositioning the Cam Sensor will often repair the condition that set the DTC.

      Were any problems found?

      Yes 

      • Perform the appropriate repair. Refer to appropriate service information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Go To  4
  4. CHECK THE VEHICLE'S REPAIR HISTORY 
    1. Check the history of the vehicle for previous crank sensor related DTCs within the past 90 days.

      Did the repair history show that the vehicle was in dealership for a Cam Sensor fault within the past 90 days?

      Yes 

      • Replace the Cam Sensor in accordance with the service information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Test complete. Reconnect the harness connectors, and erase the DTC. The most likely cause was a poor connection at one of the harness connectors. Verify the DTC does not return.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  5. CHECK THE (F856) 5-VOLT SUPPLY CIRCUIT VOLTAGE 
    Fig 1: Measuring Voltage Of 5-Volt Supply Circuit In Camshaft Position Sensor Harness Connector
    GC0097481Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Disconnect the Camshaft Position Sensor harness connector.
    3. Turn the ignition on.
    4. Measure the voltage between the (F856) 5-Volt Supply circuit and the (K900) Ground circuit at the Camshaft Position Sensor harness connector.

      Is the voltage between 4.8 and 5.2 volts?

      Yes 

      • Go To  6

      No 

      • Go To  11
  6. CHECK THE (K44) CMP SIGNAL CIRCUIT VOLTAGE 
    Fig 2: Measuring Voltage Of CMP Signal Circuit In Camshaft Position Sensor Harness Connector
    GC0097482Courtesy of CHRYSLER GROUP, LLC
    1. Measure the voltage of the (K44) CMP Signal circuit in the Camshaft Position Sensor harness connector.

      Is the voltage between 4.8 and 5.2 volts?

      Yes 

      • Go To  7

      No 

      • Go To  16
  7. CHECK FOR THE (F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO THE (K44) CMP SIGNAL CIRCUIT 
    Fig 3: Measuring Resistance Between 5-Volt Supply Circuit And CMP Signal Circuit In Camshaft Position Sensor Harness Connector
    GC0097484Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Disconnect the PCM C2 harness connector.
    3. Measure the resistance between the (F856) 5-Volt Supply circuit and the (K44) CMP Signal circuit at the Camshaft Position Sensor harness connector.

      Is the resistance above 10k Ohms?

      Yes 

      • Go To  8

      No 

      • Repair the (F856) 5-Volt Supply circuit for a short to the (K44) CMP Signal circuit.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  8. TONE WHEEL/PULSE RING INSPECTION 
    1. Turn the ignition off.
    2. Disconnect the battery ground cable.
    3. Remove the CMP Sensor.
    4. Visually inspect the sensor mounting location for damage, foreign material.
    5. Rotate the engine and if possible inspect the target wheel for any signs of damage.

      Were any problems found?

      Yes 

      • Repair Issues in mounting location. Repair or replace the Tone Wheel / Pulse Ring as necessary.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Go To  9
  9. CAMSHAFT POSITION SENSOR 
    1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Camshaft Position Sensor and the Powertrain Control Module (PCM).
    2. Look for any chafed, pierced, pinched or partially broken wires.
    3. Look for broken, bent, pushed out or corroded terminals.
    4. Replace the Camshaft Position Sensor in accordance with the service information. Refer to SENSOR, CAMSHAFT POSITION, REMOVAL .
    5. Turn the ignition on.
    6. With the scan tool, erase DTCs.
    7. Start the engine or crank the engine for ten seconds.

      Did the DTC return?

      Yes 

      • Go To  10

      No 

      • Repair complete.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  10. POWERTRAIN CONTROL MODULE (PCM) 
    1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Camshaft Position Sensor and the Powertrain Control Module (PCM).
    2. Look for any chafed, pierced, pinched or partially broken wires.
    3. Look for broken, bent, pushed out or corroded terminals.
    4. Monitor the scan tool data relative to this circuit and wiggle test the wiring and connectors.
    5. Look for the data to change or for the DTC to reset during the wiggle test.

      Were any problems found?

      Yes 

      • Repair as necessary.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

  11. CHECK THE (F856) 5-VOLT SUPPLY CIRCUIT FOR A SHORT TO VOLTAGE 
    Fig 4: Measuring Voltage Of 5-Volt Supply Circuit In Camshaft Position Sensor Harness Connector
    GC0097481Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Turn the ignition on.
    3. Measure the voltage of the (F856) 5-Volt Supply circuit at the Camshaft Position Sensor harness connector.

      Is there any voltage present?

      Yes 

      • Repair the (F856) 5-Volt Supply circuit for a short to voltage.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Go To  12
  12. CHECK THE (F856) 5-VOLT SUPPLY CIRCUIT FOR A SHORT TO GROUND 
    Fig 5: Measuring Resistance Between Ground And 5-Volt Supply Circuit In Camshaft Position Sensor Harness Connector
    GC0097485Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Disconnect the PCM C2 harness connector.
    3. Measure the resistance between ground and the (F856) 5-Volt Supply circuit in the Camshaft Position Sensor harness connector.

      Is the resistance above 10k Ohms?

      Yes 

      • Go To  13

      No 

      • Repair the (F856) 5-Volt Supply circuit for a short to ground.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  13. CHECK FOR THE (F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT 
    Fig 6: Measuring Resistance Between 5-Volt Supply Circuit And Sensor Ground Circuit In Camshaft Position Sensor Harness Connector
    GC0097486Courtesy of CHRYSLER GROUP, LLC
    1. Measure the resistance between the (F856) 5-Volt Supply circuit and the (K900) Sensor Ground circuit in the Camshaft Position Sensor harness connector.

      Is the resistance above 10k Ohms?

      Yes 

      • Go To  14

      No 

      • Repair the (F856) 5-Volt Supply circuit for a short to the (K900) Sensor Ground circuit.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  14. CHECK THE (F856) 5-VOLT SUPPLY CIRCUIT FOR AN OPEN OR HIGH RESISTANCE 
    CAUTION:

    Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install the GPEC Diagnostic Adaptor to perform the diagnosis.

    1. Connect the (special tool #10436, Adapter, GPEC Diagnostic).
    2. Measure the resistance of the (F856) 5-Volt Supply circuit between the Camshaft Position Sensor harness connector and the GPEC Adaptor.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  15

      No 

      • Repair the (F856) 5-Volt Supply circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  15. CHECK THE (K900) SENSOR GROUND CIRCUIT OPEN OR HIGH RESISTANCE 
    1. Measure the resistance of the (K900) Sensor Ground circuit between the Camshaft Position Sensor harness connector and the GPEC Adaptor.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  21

      No 

      • Repair the (K900) Sensor Ground circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  16. CHECK THE (K44) CMP SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE 
    Fig 7: Measuring Voltage Of CMP Signal Circuit In Camshaft Position Sensor Harness Connector
    GC0097482Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Disconnect the PCM C2 harness connector.
    3. Turn the ignition on.
    4. Measure the voltage of the (K44) CMP Signal circuit in the Camshaft Position Sensor harness connector.

      Is there any voltage present?

      Yes 

      • Repair the (K44) CMP Signal circuit for a short to voltage.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Go To  17
  17. CHECK THE (K44) CMP SIGNAL CIRCUIT FOR A SHORT TO GROUND 
    Fig 8: Measuring Resistance Between Ground And CMP Signal Circuit In Camshaft Position Sensor Harness Connector
    GC0097488Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Measure the resistance between ground and the (K44) CMP Signal circuit in the Camshaft Position Sensor harness connector.

      Is the resistance above 10k Ohms?

      Yes 

      • Go To  18

      No 

      • Repair the (K44) CMP Signal circuit for a short to ground.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  18. CHECK FOR THE (K44) CMP SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT 
    Fig 9: Measuring Resistance Between CMP Signal Circuit And Sensor Ground Circuit In Camshaft Position Sensor Harness Connector
    GC0097489Courtesy of CHRYSLER GROUP, LLC
    1. Measure the resistance between the (K44) CMP Signal circuit and the (K900) Sensor Ground circuit at the Camshaft Position Sensor harness connector.

      Is the resistance above 10k Ohms?

      Yes 

      • Go To  19

      No 

      • Repair the (K44) CMP Signal circuit for a short to the (K900) Sensor Ground circuit.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  19. CHECK THE (K44) CMP SIGNAL CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    CAUTION:

    Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install the GPEC Diagnostic Adaptor to perform the diagnosis.

    1. Connect the (special tool #10436, Adapter, GPEC Diagnostic).
    2. Measure the resistance of the (K44) CMP Signal circuit between the Camshaft Position Sensor harness connector and the GPEC Adaptor.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  20

      No 

      • Repair the (K44) CMP Signal circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  20. CHECK THE (K900) SENSOR GROUND CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. Measure the resistance of the (K900) Sensor Ground circuit between the Camshaft Position Sensor harness connector and the GPEC Adaptor.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  21

      No 

      • Repair the (K900) Sensor Ground circuit for an open circuit or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  21. TONE WHEEL/PULSE RING INSPECTION 
    1. Turn the ignition off.
    2. Disconnect the battery ground cable.
    3. Remove the CMP Sensor.
    4. Visually inspect the sensor mounting location for damage, foreign material.
    5. Rotate the engine and if possible inspect the target wheel for any signs of damage.

      Were any problems found?

      Yes 

      • Repair Issues in mounting location. Repair or replace the Tone Wheel / Pulse Ring as necessary.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Go To  22
  22. CAMSHAFT POSITION SENSOR 
    1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Camshaft Position Sensor and the Powertrain Control Module (PCM).
    2. Look for any chafed, pierced, pinched or partially broken wires.
    3. Look for broken, bent, pushed out or corroded terminals.
    4. Replace the Camshaft Position Sensor in accordance with the service information. Refer to SENSOR, CAMSHAFT POSITION, REMOVAL .
    5. Turn the ignition on.
    6. With the scan tool, erase DTCs.
    7. Start the engine or crank the engine for ten seconds.

      Did the DTC return?

      Yes 

      • Go To  23

      No 

      • Repair is complete.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  23. POWERTRAIN CONTROL MODULE (PCM) 
    1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Camshaft Position Sensor and the Powertrain Control Module (PCM).
    2. Look for any chafed, pierced, pinched or partially broken wires.
    3. Look for broken, bent, pushed out or corroded terminals.
    4. Monitor the scan tool data relative to this circuit and wiggle test the wiring and connectors.
    5. Look for the data to change or for the DTC to reset during the wiggle test.
      NOTE:

      Due to the fact that this DTC is set by an intermittent loss of the signal, the most likely cause is a poor connection at the Crank Sensor or PCM terminals, or a poor signal between the Crank Sensor and target wheel. Because of this, unplugging and reconnecting the harness connectors, or repositioning the Crank Sensor will often repair the condition that set the DTC.

      Were any problems found?

      Yes 

      • Repair as necessary.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

scientia non olet · About LEMON Manuals