Diagnostic Test

WARNING: This page is about a different car, the 2012 RAM Pickup. However, it is still accessible from the selected car via links, so may be relevant.

DTC IS ACTIVE
1. Ignition on, engine not running.
2. With the scan tool, record and erase DTCs.
3. Test drive the vehicle.
4. Ignition on, engine not running.
5. With the scan tool, read DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Go To 2.
  No
  - Go To 7.
(T315) STEP MOTOR CONTROL A CIRCUIT OPEN

Fig 1: Checking Step Motor Control A Circuit For An Open Or High Resistance
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off to the lock position
2. Disconnect the Transfer Case Motor harness connector.
3. Disconnect the DTCM C2 harness connector.
4. Measure the resistance of the (T315) Step Motor Control A circuit from the Transfer Case Motor harness connector to the DTCM C2 harness connector.
  Is the resistance above 5.0 Ohms?
  
  Yes
  - Repair the (T315) Step Motor Control B circuit for an open.
  - Refer to STANDARD PROCEDURE and perform the TRANSFER CASE VERIFICATION TEST.
  No
  - Go To 3.
(T316) STEP MOTOR CONTROL B CIRCUIT OPEN

Fig 2: Checking Step Motor Control B Circuit For An Open Or High Resistance
Courtesy of CHRYSLER GROUP, LLC
1. Measure the resistance of the (T316) Step Motor Control C circuit from the Transfer Case Motor harness connector to the Final Drive Control Module C2 harness connector.
  Is the resistance above 5.0 Ohms?
  
  Yes
  - Repair the (T316) Step Motor Control C circuit for an open.
  - Refer to STANDARD PROCEDURE and perform the TRANSFER CASE VERIFICATION TEST.
  No
  - Go To 4.
(T315) STEP MOTOR CONTROL A CIRCUIT SHORTED TO VOLTAGE

Fig 3: Checking Step Motor Control A Circuit For Short To Voltage
Courtesy of CHRYSLER GROUP, LLC
1. Ignition on, engine not running.
2. Measure the voltage of the (T315) Step Motor Control A circuit at the Transfer Case Motor harness connector.
  Is the voltage above 0.5 of a volt?
  
  Yes
  - Repair the (T315) Step Motor Control A circuit for a short to voltage.
  - Refer to STANDARD PROCEDURE and perform the TRANSFER CASE VERIFICATION TEST.
  No
  - Go To 5.
(T316) STEP MOTOR CONTROL B CIRCUIT SHORTED TO VOLTAGE

Fig 4: Checking Step Motor Control B Circuit For Short To Voltage
Courtesy of CHRYSLER GROUP, LLC
1. Measure the voltage of the (T316) Step Motor Control B circuit at the Transfer Case Motor harness connector.
  Is the voltage above 0.5 of a volt?
  
  Yes
  - Repair the (T316) Step Motor Control B circuit for a short to voltage.
  - Refer to STANDARD PROCEDURE and perform the TRANSFER CASE VERIFICATION TEST.
  No
  - Go To 6.
TRANSFER CASE SHIFT MOTOR/MODE SENSOR ASSEMBLY

Fig 5: Checking Transfer Case Shift Motor/Mode Sensor Assembly
Courtesy of CHRYSLER GROUP, LLC
1. Connect the Transfer Case Shift Motor/Mode Sensor Assembly harness connector.
2. Measure the resistance between the (T315) Step Motor Control A circuit and the (T316) Step Motor Control B circuit at the Final Drive Control Module C2 harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Replace the Drive Train Control Module (DTCM) in accordance with the Service Information.
  - Refer to STANDARD PROCEDURE and perform the DTCM VERIFICATION TEST.
  No
  - Replace the shorted Transfer Case Shift Motor/Mode Sensor Assembly in accordance with the Service Information.
  - Refer to STANDARD PROCEDURE and perform the TRANSFER CASE VERIFICATION TEST.
INTERMITTENT WIRING HARNESS AND CONNECTORS
1. The conditions necessary to set this DTC are not present at this time.
2. Using the wiring diagram/schematic as a guide, inspect the wiring harness and connectors.
3. Wiggle test the wiring harness and connectors while monitoring the scan tool data relative to this circuit.
4. Look for the data to change or for the DTC to reset during the wiggle test.
5. While monitoring the scan tool data relative to this circuit, move the selector switch to each position several times.
6. Look for the data to change other than as expected or for the DTC to reset.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Refer to STANDARD PROCEDURE and perform the TRANSFER CASE VERIFICATION TEST.
  No
  - Test complete.