Technical Specifications: Specifications
WARNING: This page is about a different car, the 2017 RAM 2500 HD. However, it is still accessible from the selected car via links, so may be relevant.
GENERAL
| Component | Metric | Inch |
|---|---|---|
| Output Shaft End Play | 0.25-0.52 mm | 0.010-0.020 in. |
| Input Shaft End Play | 0.52-0.74 mm | 0.020-0.029 in. |
| 2C Clutch Pack Clearance | 0.99-1.65 mm | 0.039-0.065 in. |
| 4C Clutch Pack Clearance | 0.770-1.390 mm | 0.030-0.055 in. |
| L/R Clutch Pack Clearance | 1.18-2.09 mm | 0.046-0.082 in. |
| OD Clutch Pack Clearance | 0.75-1.61 mm | 0.030-0.063 in. |
| UD Clutch Pack Clearance | 1.02-1.72 mm | 0.040-0.068 in. |
| Reverse Clutch Pack Clearance | 0.58-1.47 mm | 0.023-0.058 in. |
GEAR RATIOS
| 1ST | 3.23:1 |
| 2ND | 1.83:1 |
| 3RD | 1.41:1 |
| 4TH | 1.0:1 |
| 5TH | 0.81:1 |
| 6TH | 0.62:1 |
| REVERSE | 4.44:1 |
TORQUE SPECIFICATIONS
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. |
|---|---|---|---|
| Accumulator cover screw | 7 | - | 60 |
| For rear mount specifications | Refer to TORQUE SPECIFICATIONS for 5.7L or TORQUE SPECIFICATIONS for 6.4L . | ||
| Converter housing bolt | 68 | 50 | - |
| Cooler line at trans fitting | 17.5 | - | 155 |
| Cooler return filter | 9.5 | - | 84 |
| Detent spring screw | 4.5 | - | 40 |
| Driveplate to crankshaft bolt | 75 | 55 | - |
| Extension housing bolt | 54 | 40 | - |
| Fill tube at transmission bolt | 10 | - | 88 |
| Fill tube at valve cover nut | 10 | - | 88 |
| Input speed sensor bolt | 12 | - | 105 |
| Inspection cover bolt | 10 | - | 88 |
| Line pressure sensor bolt | 12 | - | 105 |
| Manual selector shaft cross-bolt | 16 | - | 140 |
| Manual selector shaft retaining screw | 28 | 21 | - |
| Manual valve cam retaining screw | 4.5 | - | 40 |
| Oil pan bolts | 12 | - | 105 |
| Oil pump body to cover bolts | 4.5 | - | 40 |
| Oil pump bolt | 28 | 21 | - |
| Output speed sensor bolt | 12 | - | 105 |
| Plate to oil pump body screw | 4.5 | - | 40 |
| Pressure test port plug | 5 | - | 45 |
| Primary fluid filter screw | 4.5 | - | 40 |
| Reaction shaft support bolt | 12 | - | 105 |
| Solenoid module to transfer plate screw | 6 | - | 50 |
| Torque converter housing to engine lower four bolt | 54 | 40 | - |
| Torque converter housing to engine upper four bolts | 41 | 30 | - |
| Torque converter to driveplate bolt | 88 | 65 | - |
| Transmission collar bolt | 68 | 50 | - |
| Transfer case nuts | 35 | 26 | - |
| Valve body to case bolts | 12 | - | 105 |
| Valve body to transfer plate screw | 5.5 | - | 50 |