LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2011 >> 300 C, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 959 (5.7L - DTCS P0602 To P2101 - 2500 Hd & 3500 Hd) >> Diagnosis And Testing >> P1E09-Closed Loop Fueling Not Achieved - Bank 1 Downstream >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2015 RAM 3500 HD and 2015 RAM 2500 HD. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FOR AN ACTIVE DTC 
    1. Diagnose and repair any other active component or circuit DTCs before continuing with this procedure.
    2. Turn the ignition on.
    3. With the scan tool, read DTCs and record on the repair order. Copy DTC and Freeze Frame information.
    4. Start the engine and allow it to reach operating temperature.
      WARNING:

      When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.

      NOTE:

      Attempt to operate the vehicle under conditions similar to which the DTC was set.

      NOTE:

      It may be necessary to test drive the vehicle within the DTC monitoring conditions in order for this DTC to set.

    5. With the scan tool, read DTCs and record on the repair order.

      Is the DTC active or pending?

      Yes 

      • Go To  2

      No 

  2. CHECK THE FUEL DELIVERY SYSTEM 
    1. Perform the diagnostic procedures for FUEL PRESSURE LEAK DOWN and FUEL DELIVERY SYSTEM OUTPUT - FLOW TEST. Refer to DIAGNOSIS AND TESTING .

      Were any problems found?

      Yes 

      • Repair as necessary in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  3
  3. CHECK THE ENGINE COOLANT TEMPERATURE SENSOR OPERATION 
    1. Perform the diagnostic procedure for CHECKING THE ENGINE COOLANT TEMPERATURE SENSOR OPERATION. Refer to DIAGNOSIS AND TESTING .

      Were any problems found?

      Yes 

      • Repair as necessary in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  4
  4. CHECK THE MAP SENSOR OPERATION 
    1. Perform the diagnostic procedure for CHECKING THE MAP SENSOR OPERATION. Refer to DIAGNOSIS AND TESTING .

      Were any problems found?

      Yes 

      • Repair as necessary in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  5
  5. CHECK THE OXYGEN SENSOR OPERATION 
    1. Perform the diagnostic procedure for CHECKING THE OXYGEN SENSOR OPERATION. Refer to DIAGNOSIS AND TESTING .

      Were any problems found?

      Yes 

      • Repair as necessary in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  6
  6. CHECK THE ENGINE MECHANICAL SYSTEM 
    1. Perform the diagnostic procedure for CHECKING THE ENGINE MECHANICAL SYSTEM. Refer to DIAGNOSIS AND TESTING .

      Were any problems found?

      Yes 

      • Repair as necessary in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  7
  7. CHECK RELATED PCM AND COMPONENT CONNECTIONS 
    1. Perform any Service Bulletins that apply.
    2. Disconnect all PCM harness connectors.
    3. Disconnect all related in-line harness connections (if equipped).
    4. Disconnect the related component harness connectors.
    5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Check for spread terminals and verify proper terminal tension.

      Repair any conditions that are found.

    6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    9. With the scan tool, erase DTCs.
    10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
    11. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      No 

scientia non olet · About LEMON Manuals