Diagnostic Test

WARNING: This page is about a different car, the 2015 RAM 1500. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR RELATED DTCS
1. With the scan tool, read TCM DTCs.
  Are any Transmission solenoid, line pressure, speed sensor, and or loss of prime DTCs set?
  
  Yes
  - Repair Transmission solenoid, line pressure, speed sensor, and or loss of prime DTCs. If DTC P0944 is set, perform that diagnostic procedure first. Refer to DIAGNOSTIC CODE INDEX - 65RFE AUTOMATIC TRANSMISSION - 1500 article .
  No
  - Go To 2
CHECK FOR EVENT DATA FOR DTC P0735
1. With the scan tool, read and record the Event Data.
  NOTE:
  Make sure to record all Event Data stored in the scan tool for future reference in this test procedure.
  
  Does the Event Data display information for DTC P0735?
  
  Yes
  - Go To 4
  No
  - Go To 3
CHECK FOR EVENT DATA FOR DTC P1790
In the Event Data recorded earlier, does the Event Data show DTC P1790, with Target gear = 5th or with both the 2C and OD clutches applying?

Yes
- Go To 4
No
- Go To 6
CHECK INPUT RPM
In the Event Data recorded earlier, does the Input RPM read zero?

Yes
- Perform the diagnostic procedure for P0716. Diagnose the DTC as if it is active. Refer to DIAGNOSTIC CODE INDEX - 65RFE AUTOMATIC TRANSMISSION - 1500 article .
No
- Go To 5
CHECK LINE PRESSURE READING
In the Event Data recorded earlier, is the line pressure reading more than 10 psi below the desired line pressure reading?

Yes
- Remove the Transmission Oil pan and check the Transmission Oil filter for improper installation or plugged, if Primary oil filter is OK, check the main regulator valve in pump. If excessive debris is in the oil pan, check clutches and repair as necessary.
- Perform the TRANSMISSION VERIFICATION TEST. Refer to 65RFE TRANSMISSION VERIFICATION TEST .
No
- Go To 6
CHECK TRANSMISSION FOR SLIPPAGE
1. With the scan tool, erase DTCs.
2. Road test the vehicle and check the Transmission operation in reverse and all forward gears.
  During the road test, was there any obvious slippage noted in 5th gear or a runaway during the 4-5 shift?
  
  Yes
  - Go To 8
  No
  - Go To 7
CHECK IF DTC RETURNS
1. With the scan tool, check for transmission DTCs.
  Did DTC P0735 return?
  
  Yes
  - Go To 8
  No
  - Test complete.
CHECK INTERNAL TRANSMISSION
1. Remove the Transmission Oil Pan and Valve Body, in accordance with the Service Information, and check for the following:
  - Excessive clutch and or metal debris in the oil pan.
  - If the accumulator cover is intact and the 2C tower seal is not cut or split.
  - OD and 2C accumulator pistons for cracks or cut seals.
  - Solenoid Switch Valve and Plugs for stickiness or wear.
  - Cut or missing No. 5, No. 6, or No. 7 check ball.
  - OD bleed orifice on top of the valve body.
  - Air check the OD and 2C hydraulic clutch circuits for excessive leakage. Refer to the Service information.
  NOTE:
  Both the OD and 2C hydraulic clutch circuits contain a small bleed orifice. A small amount of air leakage is considered normal. The OD hydraulic clutch circuit bleed orifice connects to the Reverse input clutch hydraulic cavity. A small amount of air leakage into the Reverse hydraulic clutch circuit is considered normal.
  
  Were any problems found?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
    NOTE:
    If the OD or 2C clutch has failed but no obvious cause is found (such as a cut piston seal, broken seal ring, stuck regulator valve or any other items listed above) replace the Transmission Solenoid/TRS Assembly in addition to any necessary internal repairs.
  - Perform the TRANSMISSION VERIFICATION TEST. Refer to 65RFE TRANSMISSION VERIFICATION TEST .
  No
  - Replace Transmission Solenoid/TRS Assembly in accordance with the Service Information.
  - Perform the TRANSMISSION VERIFICATION TEST. Refer to 65RFE TRANSMISSION VERIFICATION TEST .