LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2011 >> 300 C, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 795 (8HP45/845RE Automatic Transmission (Service Information) - 1500) >> Valve Body >> Installation >> Installation

Valve Body: Installation: Installation

WARNING: This page is about a different car, the 2015 RAM 1500. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:

The Transmission Control Module (TCM), or Transmission Control Module Assembly (TCMA) is extremely sensitive to Electrostatic Discharge (ESD). Always use a ground strap and follow the ESD guidelines in ELECTROSTATIC DISCHARGE (ESD) SENSITIVE DEVICES. Failure to follow these instructions may result in damage to the TCM/TCMA.

Fig 1: Fluid Port, O-Rings & Compression Seal
GC0152241Courtesy of CHRYSLER GROUP, LLC
  1. Install the fluid port (1) with new  O-rings (2) and seal (3) to the valve body.
    Fig 2: Valve Body Alignment Pins
    GC0152262Courtesy of CHRYSLER GROUP, LLC
  2. Install the valve body assembly to the transmission using the previously installed (1) (special tool #10379, Pins, Valve Body Alignment) as a guide.
  3. Use an appropriate tool on one of the alignment pins to assist in holding the valve body in position while installing the remaining fasteners.
    Fig 3: Valve Body Bolts Loosening And Tightening Sequence
    GC0169780Courtesy of CHRYSLER GROUP, LLC
  4. Install the valve body assembly retaining bolts not including 16-18 and hand tighten.
  5. Remove the pins and install the remaining bolts.
    Fig 4: Remover/Installer, Guide Sleeve, Electrical Harness Insulator & Transmission Case
    GC0152117Courtesy of CHRYSLER GROUP, LLC
  6. Using (special tool #10377, Remover/Installer, Guide Sleeve) (1) carefully install the electrical harness insulator (2) to the transmission case (3).
    Fig 5: Speed Sensor, Electrical Connector Lock & Valve Body Assembly End Retainer Bolts
    GC0152103Courtesy of CHRYSLER GROUP, LLC
  7. Lock the electrical connector lock (2) to the internal harness end.
  8. Install the speed sensor (4) to the case install the retaining bolt (1) and tighten to 8 N.m (71 in. lbs.).
    Fig 6: Hydraulic Impulse Oil Storage Accumulator & Bolts
    GC0154626Courtesy of CHRYSLER GROUP, LLC
  9. If equipped, install the Hydraulic Impulse Oil Storage (H.I.S.) accumulator (1).
  10. Tighten the bolts (2 and 3) to 8 N.m (71 in. lbs.).
  11. Connect the H.I.S. electrical connector.
  12. Install the valve body assembly end retainer bolts (3) and hand tighten.
    Fig 7: Valve Body Bolts Loosening And Tightening Sequence
    GC0169780Courtesy of CHRYSLER GROUP, LLC
  13. Tighten the valve body fasteners to 8 N.m (71 in. lbs.).
    Fig 8: Manual Park Release Lever & Retaining Nut
    GC0152243Courtesy of CHRYSLER GROUP, LLC
  14. Remove the tie strap and return the manual release lever (1) to the original position, tighten the fastener (2) to 35 N.m (26 ft. lbs.).
    Fig 9: Oil Pan Retaining Bolts Tightening Sequence
    GC0152239Courtesy of CHRYSLER GROUP, LLC
  15. Install the oil pan and gasket.
  16. Install the thirteen oil pan retaining bolts and tighten the fasteners to 10 N.m (89 in. lbs.) using the sequence given.
    Fig 10: Adapter Plug Connector
    GC0152193Courtesy of CHRYSLER GROUP, LLC
  17. Connect the plug connector (1).
    Fig 11: Locking Mechanism Lock & Adapter Plug Connector
    GC0152192Courtesy of CHRYSLER GROUP, LLC
  18. Turn the locking mechanism (1) of the harness plug clockwise and lock in place.
  19. If the valve body is replaced, program the TCM. Refer to MODULE, TRANSMISSION CONTROL, MODULE PROGRAMMING .
  20. Perform the TRANSMISSION FILL AFTER SERVICE procedure. Refer to FLUID AND FILTER, STANDARD PROCEDURE .
  21. Perform the TRANSMISSION VERIFICATION TEST. Refer to TRANSMISSION VERIFICATION TEST . .
scientia non olet · About LEMON Manuals