Diagnostic Test

WARNING: This page is about a different car, the 2013 Dodge Avenger and 2013 Chrysler 200. However, it is still accessible from the selected car via links, so may be relevant.

VERIFY DTC IS ACTIVE
NOTE:
If present, diagnose and repair DTC U0125-LOST COMMUNICATION WITH DYNAMICS SENSOR before diagnosing this DTC.
1. Turn the ignition on.
2. With the scan tool, read and record the ABS DTCs.
3. With the scan tool, read and record Environmental Data to help identify the conditions in which the DTC was set.
4. With the scan tool, erase the ABS DTCs.
5. Cycle the ignition switch.
6. With the scan tool, read the ABS DTCs.
  Does this DTC reset?
  
  Yes
  - Go To 2
  No
  - The condition that caused the symptom is currently not present. Inspect the related wiring for a possible intermittent condition. Look for any chafed, pierced, pinched, or partially broken wires.
  - Perform the ABS INTERMITTENT CONDITION TEST. Refer to STANDARD PROCEDURE .
INSPECT RELATED WIRING HARNESS, TERMINALS, AND CONNECTORS
1. Visually inspect the related wiring harness. Look for any pinched, chafed, pierced, and partially broken wires.
2. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, and corroded terminals.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform ABS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 3
CHECK THE (D465) DYNAMICS SENSOR HIGH DATA LINK CIRCUIT FOR A SHORT TO VOLTAGE

Fig 1: Measuring Voltage Of Dynamics Sensor High Data Link Circuit
Courtesy of CHRYSLER GROUP, LLC
1. Disconnect the Anti-Lock Brake Module harness connector.
2. Disconnect the Dynamics Sensor harness connector.
3. Turn the ignition on.
4. Measure the voltage of the (D465) Dynamics Sensor High Data Link circuit.
  Is there any voltage present?
  
  Yes
  - Repair the (D465) Dynamics Sensor High Data Link circuit for a short to voltage.
  - Perform ABS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 4
CHECK THE (D465) DYNAMICS SENSOR HIGH DATA LINK CIRCUIT FOR A SHORT TO GROUND

Fig 2: Checking Dynamics Sensor Low Data Link Circuit For A Short To Ground
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Measure the resistance of the (D465) Dynamics Sensor High Data Link circuit between ground and the Dynamics Sensor harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Repair the (D465) Dynamics Sensor High Data Link circuit for a short to ground.
  - Perform ABS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 5
CHECK THE (D465) DYNAMICS SENSOR HIGH DATA LINK CIRCUIT FOR AN OPEN

Fig 3: Checking Dynamics Sensor High Data Link Circuit For An Open
Courtesy of CHRYSLER GROUP, LLC
1. Measure the resistance of the (D465) Dynamics Sensor High Data Link circuit between the Dynamics Sensor harness connector and the Anti-Lock Brake Module harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Go To 6
  No
  - Repair the (D465) Dynamics Sensor High Data Link circuit for an open.
  - Perform ABS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK THE (D464) DYNAMICS SENSOR LOW DATA LINK CIRCUIT FOR A SHORT TO VOLTAGE

Fig 4: Measuring Voltage Of Dynamics Sensor Low Data Link Circuit
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition on.
2. Measure the voltage of the (D464) Dynamics Sensor Low Data Link circuit.
  Is there any voltage present?
  
  Yes
  - Repair the (D464) Dynamics Sensor Low Data Link circuit for a short to voltage.
  - Perform ABS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 7
CHECK THE (D464) DYNAMICS SENSOR LOW DATA LINK CIRCUIT FOR A SHORT TO GROUND

Fig 5: Measuring Resistance Between Ground & Dynamics Sensor High Data Link Circuit
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Measure the resistance of the (D464) Dynamics Sensor Low Data Link circuit between ground and the Dynamics Sensor harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Repair the (D464) Dynamics Sensor Low Data Link circuit for a short to ground.
  - Perform ABS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 8
CHECK THE (D464) DYNAMICS SENSOR LOW DATA LINK CIRCUIT FOR AN OPEN

Fig 6: Checking Dynamics Sensor Low Data Link Circuit For An Open
Courtesy of CHRYSLER GROUP, LLC
1. Measure the resistance of the (D464) Dynamics Sensor Low Data Link circuit between the Dynamics Sensor harness connector and the Anti-Lock Brake Module harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Go To 9
  No
  - Repair the (D464) Dynamics Sensor Low Data Link circuit for an open.
  - Perform ABS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
REPLACE DYNAMICS SENSOR AND VERIFY IF DTC IS STILL ACTIVE
1. Replace the Dynamics Sensor in accordance with the Service Information. Perform ABS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
2. Turn the ignition on.
3. With the scan tool, erase ABS DTCs.
4. Cycle the ignition switch.
  WARNING:
  Make sure brake capability is available before road testing.
5. Test drive the vehicle by turning the vehicle left or right in a curving manner at a velocity between 6 and 15 mph (10 and 25 km/h).
6. Park the vehicle.
7. With the scan tool, read ABS DTCs.
  Does this DTC reset?
  
  Yes
  - Replace the Anti-Lock Brake Module in accordance with the Service Information.
  - Perform ABS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Test complete.