Diagnostic Test

WARNING: This page is about a different car, the 2013 RAM 1500. However, it is still accessible from the selected car via links, so may be relevant.

ACTIVE DTC
NOTE:
When this DTC is Active, the engine speed, torque and vehicle speed are limited to a Limp in mode.

NOTE:
If P2072 is also set, this indicates that the cold weather ice blockage routine has run. No repair action is required.
1. Ignition on, engine not running.
  NOTE:
  If the P2118 is intermittent, it is possible that the controller is overheating in extreme hot temperatures and this is considered a normal protection operation. No repair is necessary.
2. With the scan tool, read the active DTCs.
3. Look closely at the temperatures at which this DTC set.
  Is the DTC Active at this time?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to STANDARD PROCEDURE .
THROTTLE PLATE INSPECTION
1. Turn the ignition off.
2. Remove the Air Cleaner Assembly from the Throttle Body. Refer to THROTTLE BODY, REMOVAL .
3. Check for any signs of a foreign material (ice or dirt) on the Throttle Plate or in the bore causing the Throttle Plate to stick.
  Were any signs of foreign material or scoring of the throttle plate or bore found?
  
  Yes
  - Remove the debris if possible or replace the Throttle Body Assembly. Refer to THROTTLE BODY, REMOVAL . Disconnect the Battery when replacing the Throttle Body Assembly. After installation is complete, use a scan tool and select the ETC RELEARN function.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 3
CHECK THE (K447) ETC POSITIVE CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition off.
2. Disconnect the Throttle Body harness connector.
3. Disconnect the PCM C2 harness connector.
4. Ignition on, engine not running.
5. Measure the voltage on the (K447) ETC Positive circuit at the Throttle Body harness connector.
  Is there any voltage present?
  
  Yes
  - Repair the (K447) ETC Positive circuit for a short to voltage.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 4
CHECK THE (K448) ETC NEGATIVE CIRCUIT FOR A SHORT TO VOLTAGE
1. Measure the voltage on the (K448) ETC Negative circuit at the Throttle Body harness connector.
  Is there any voltage present
  
  Yes
  - Repair the (K448) ETC Negative circuit for a short to voltage.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 5
CHECK FOR THE (K447) ETC POSITIVE CIRCUIT SHORTED TO THE (K448) ETC NEGATIVE CIRCUIT
1. Turn the ignition off.
  CAUTION:
  Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install the GPEC Diagnostic Adaptor to perform the diagnosis.
2. Connect the (special tool #10436, Adapter, GPEC Diagnostic).
3. Measure the resistance between the (K447) ETC Positive circuit and the (K448) ETC Negative circuit at the GPEC Adaptor.
  Is the resistance above 10k Ohms?
  
  Yes
  - Go To 6
  No
  - Repair the short between the (K447) ETC Positive circuit and the (K448) ETC Negative circuit.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK THE (K447) ETC POSITIVE CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Measure the resistance of the (K447) ETC Positive circuit from the Throttle Body harness connector to the GPEC Adaptor.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Go To 7
  No
  - Repair the (K447) ETC Positive circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK THE (K447) ETC POSITIVE CIRCUIT FOR A SHORT TO GROUND
1. Measure the resistance between a known good ground and the (K447) ETC Positive circuit at the Throttle Body harness connector.
  Is the resistance above 10k Ohms?
  
  Yes
  - Go To 8
  No
  - Repair the (K447) ETC Positive circuit for a short to ground.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK THE (K448) ETC NEGATIVE CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Measure the resistance of the (K448) ETC Negative circuit from the Throttle Body harness connector to the GPEC Adaptor.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Go To 9
  No
  - Repair the (K448) ETC Negative circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK THE (K448) ETC NEGATIVE CIRCUIT FOR A SHORT TO GROUND
1. Measure the resistance between a known good ground and the (K448) ETC Negative circuit at the Throttle Body harness connector.
  Is the resistance above 10k Ohms?
  
  Yes
  - Go To 10
  No
  - Repair the (K448) ETC Negative circuit for a short to ground.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
ETC MOTOR
1. Connect the Throttle Body harness connector.
2. Measure the resistance of the ETC Motor between the (K447) ETC Positive circuit and the (K448) ETC Negative circuit at the GPEC Adaptor.
  Is the resistance between 2.5 and 25 Ohms at closed throttle?
  
  Yes
  - Go To 11
  No
  - Verify that there is good pin to terminal contact in the Throttle Body and Powertrain Control Module connectors. If OK, replace the Throttle Body Assembly. Refer to THROTTLE BODY, REMOVAL . Disconnect the Battery when replacing the Throttle Body Assembly. After installation is complete, use a scan tool and select the ETC RELEARN function.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
POWERTRAIN CONTROL MODULE (PCM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Throttle Body and the Powertrain Control Module (PCM).
2. Look for any chafed, pierced, pinched or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals. Verify that there is good pin to terminal contact in the Throttle Body and Powertrain Control Module connectors.
4. Perform any Technical Service Bulletins that may apply.
  Were there any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Replace and program the Powertrain Control Module in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to STANDARD PROCEDURE .