Diagnostic Test

WARNING: This page is about a different car, the 2016 RAM 3500 HD and 2016 RAM 2500 HD. However, it is still accessible from the selected car via links, so may be relevant.

DETERMINE ACTIVE OR STORED DTC
NOTE:
The use of a approved special tool or Digital Multimeter such as a Fluke Meter that will not apply more than 20 milliamperes to a circuit are the only measurement tools to be used.

NOTE:
Probing of the circuit cavities at the ORC Module C1-A, C1-B, or C2-B body harness connectors is only to be done with a approved test lead from the Test Leads, Dedicated kit 10159, test lead 10159-6. Or a comparable test lead to prevent vehicle wiring harness connector damage during diagnostic procedures. (special tool #10159, Test Leads, Dedicated)

NOTE:
Make sure the battery is fully charged.
1. Turn the ignition on.
2. With the scan tool, read ORC DTCs.
  Does the scan tool display active: B2768-87-RIGHT SIDE SATELLITE SENSOR 4 - MISSING MESSAGE?
  
  Yes
  - Go To 2
  No
  - Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. Refer to RESTRAINTS SYSTEM INTERMITTENT TEST .
CHECK THE (R140), (R160) RIGHT SIDE IMPACT PRESSURE SENSOR SIGNAL AND GROUND CIRCUITS FOR A SHORT TO VOLTAGE

Fig 1: Checking Right Side Impact Pressure Sensor Signal And Ground Circuits For A Short To Voltage
Courtesy of CHRYSLER GROUP, LLC

WARNING:
Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
1. Disconnect the Right Side Impact Pressure Sensor harness connector.
2. Disconnect the ORC harness connector.
3. If the vehicle is equipped with the standard key ignition, follow this ignition on warning.
  WARNING:
  Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
4. If the vehicle is equipped with the keyless ignition, follow this ignition on warning.
  WARNING:
  Disconnect the 12-volt battery wait two minutes before proceeding, remove the ORC fuses, connect the 12-volt battery, wait two minutes before proceeding. Cycle the ignition to the On position, then reconnect the ORC fuses. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
5. Measure the voltage of the (R140) Right Side Impact Pressure Sensor Signal circuit and (R160) Sensor Ground circuit at the appropriate terminal of the Right Side Impact Pressure Sensor harness connector and ground.
  Is there any voltage present?
  
  Yes
  - Repair the (R140), (R160) Right Side Impact Pressure Sensor circuits for a short to voltage.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS-SYSTEM-VERIFICATION-TEST .
  No
  - Go To 3
CHECK THE (R140) RIGHT SIDE IMPACT PRESSURE SENSOR SIGNAL CIRCUIT FOR A SHORT TO GROUND

Fig 2: Checking Right Side Impact Pressure Sensor Signal Circuit For Short To Ground
Courtesy of CHRYSLER GROUP, LLC

WARNING:
Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
1. Measure the resistance of the (R140) Right Side Impact Pressure Sensor Signal circuit between the appropriate terminal of the Right Side Impact Pressure Sensor harness connector and ground.
  Is the resistance below 20 Ohms?
  
  Yes
  - Repair the (R140) Right Side Impact Pressure Sensor Signal circuit for a short to ground.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS-SYSTEM-VERIFICATION-TEST .
  No
  - Go To 4
CHECK THE (R140), (R160) RIGHT SIDE IMPACT PRESSURE SENSOR CIRCUITS FOR A SHORT TOGETHER

Fig 3: Checking Right Side Impact Pressure Sensor Circuits For Short Together
Courtesy of CHRYSLER GROUP, LLC
1. Measure the resistance between the (R140) Right Side Impact Pressure Sensor 4 Signal circuit and the (R160) Sensor Ground circuits at the Right Side Impact Pressure Sensor 4 harness connector.
  Is the resistance below 20 Ohms?
  
  Yes
  - Repair the (R140), (R160) Right Side Impact Pressure Sensor circuits shorted together.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS-SYSTEM-VERIFICATION-TEST .
  No
  - Go To 5
CHECK THE (R160) RIGHT SIDE IMPACT PRESSURE SENSOR GROUND CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Connect the appropriate test lead to the DVOM.
2. Measure the resistance of the (R160) Right Side Impact Pressure Sensor Ground circuit between terminal 2 of the Right Side Impact Pressure Sensor harness connector and terminal C2-36 of the ORC module body harness connector.
  Is the resistance below 1 Ohm?
  
  Yes
  - Go To 6
  No
  - Repair the (R160) Right Side Impact Pressure Sensor Ground circuit for an open or high resistance.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS-SYSTEM-VERIFICATION-TEST .
CHECK THE (R140) RIGHT SIDE IMPACT PRESSURE SENSOR SIGNAL CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Measure the resistance of the (R140) Right Side Impact Pressure Sensor Signal circuit between terminal 1 of the Right Side Impact Pressure Sensor harness connector and terminal C2-35 of the ORC module body harness connector.
  Is the resistance below 1 Ohm?
  
  Yes
  - Go To 7
  No
  - Repair the (R140) Right Side Impact Pressure Sensor Signal circuit for an open or high resistance.
  - Perform the RESTRAINTS VERIFICATION TEST. Refer to RESTRAINTS-SYSTEM-VERIFICATION-TEST .
CHECK OPERATION OF THE RIGHT SIDE IMPACT PRESSURE SENSOR
1. Replace the Right Side Impact Pressure Sensor 4. Refer to SENSOR, IMPACT, REMOVAL .
2. Reconnect the vehicle body harness to the impact pressure sensor.
3. Remove any special tools or jumper wires and reconnect all previously disconnected components - except the Battery.
4. If the vehicle is equipped with the standard key ignition, follow this ignition on warning.
  WARNING:
  Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
5. If the vehicle is equipped with the keyless ignition, follow this ignition on warning.
  WARNING:
  Disconnect the 12-volt battery wait two minutes before proceeding, remove the ORC fuses, connect the 12-volt battery, wait two minutes before proceeding. Cycle the ignition to the On position, then reconnect the ORC fuses. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
6. Connect the scan tool to the Data Link Connector - use the most current software available.
7. Use the scan tool and erase the stored codes in all airbag system modules.
8. Turn the Ignition Off, and wait five seconds before turning the Ignition On.
9. Wait one minute, and read active codes and if there are none present read the stored codes.
  Did the active: B2768-87-RIGHT SIDE SATELLITE SENSOR 4 - MISSING MESSAGE DTC return?
  
  Yes
  
  WARNING:
  Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
  
  WARNING:
  If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment. Failure to follow these instructions may result in possible serious or fatal injury.
  - Replace the Occupant Restrain Controller (ORC) in accordance with the Service Information. Refer to MODULE, OCCUPANT RESTRAINT CONTROLLER, REMOVAL .
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS-SYSTEM-VERIFICATION-TEST .
  No
  - Repair is complete.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS-SYSTEM-VERIFICATION-TEST .