Diagnostic Test

DTC IS ACTIVE
1. Turn the ignition on.
2. With the scan tool, Clear DTCs in the Totally Integrated Power Module (TIPM).
3. With a scan tool, select Radiator Cooling Fan #1 Control State, to actuate the Cooling Fan (Low Speed).
4. With the scan tool, select View DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Go to step 2
  No
  - Perform the CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
(A16) FUSED B(+) CIRCUIT OPEN OR HIGH RESISTANCE

Fig 1: Checking Fused B(+) Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Disconnect the Radiator Cooling Fan Module harness connector.
3. Turn the ignition on.
4. Using a 12 volt test light connected to ground, check the (A16) Fused B(+) circuit in the Radiator Cooling Fan Module harness connector.
  NOTE: The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.
  
  Is the test light illuminated and bright?
  
  Yes
  - Go to step 3
  No
  - Repair the (A16) Fused B(+) circuit for an open circuit or high resistance.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
(Z903) GROUND CIRCUIT OPEN OR HIGH RESISTANCE

Fig 2: Checking Ground Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Using a 12 volt test light connected to 12 volts, check the (Z903) Ground circuit in the Radiator Cooling Fan Module harness connector.
  NOTE: The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.
  
  Is the test light illuminated and bright?
  
  Yes
  - Go to step 4
  No
  - Repair the (Z903) Ground circuit for an open circuit or high resistance.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
RADIATOR COOLING FAN MODULE
1. Turn the ignition on.
2. With a scan tool, select Radiator Cooling Fan #1 Control State, Toggle, to actuate the Cooling Fan (Low Speed).
3. Using a 12-volt test light connected to battery voltage, probe the (N201) Low Speed Rad Fan Control circuit in the Radiator Cooling Fan Module harness connector.
  Does the test light illuminate brightly and flash on and off?
  
  Yes
  - Replace the Radiator Cooling Fan Module.
  - Perform the POWERTRAIN VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
  No
  - Go to step 5
(N201) LOW SPEED RAD FAN CONTROL CIRCUIT SHORTED TO VOLTAGE

Fig 3: Checking Low Speed Radiator Fan Control Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Disconnect the Totally Integrated Power Module (TIPM) C11 harness connector.
3. Turn the ignition on.
4. Measure the voltage of the (N201) Low Speed Rad Fan Control circuit in the Radiator Cooling Fan Module harness connector.
  Is there any voltage present?
  
  Yes
  - Repair the (N201) Low Speed Rad Fan Control circuit for a short to voltage.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
  No
  - Go to step 6
(N201) LOW SPEED RAD FAN CONTROL CIRCUIT OPEN OR HIGH RESISTANCE

Fig 4: Checking Low Speed Radiator Fan Control Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Measure the resistance of the (N201) Low Speed Rad Fan Control circuit between the Radiator Cooling Fan Module harness connector and the Totally Integrated Power Module (TIPM) C11 harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Go to step 7
  No
  - Repair the (N201) Low Speed Rad Fan Control circuit for an open circuit or high resistance.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
TOTALLY INTEGRATED POWER MODULE (TIPM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Cooling Fan Module and the Totally Integrated Power Module (TIPM).
2. Look for any chafed, pierced, pinched or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals.
4. Refer to any Technical Service Bulletins that may apply.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
  No
  - Replace and program the Totally Integrated Power Module (TIPM) in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .