LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2009 >> 300 Signature Series >> Repair and Diagnosis >> External Pages >> Different car >> Section 58 (Vehicle Theft Security System - Electrical Diagnostics) >> Vehicle Theft Security - Electrical Diagnostics >> DTC Troubleshooting >> B1A2E-Key 5 Communication Error >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2006 Dodge Magnum, 2006 Dodge Charger, and 2006 Chrysler 300. However, it is still accessible from the selected car via links, so may be relevant.
  1. 1)  DETERMINING IF DTC IS CURRENT 

    With the scan tool, read and record the SKREEM DTCs.

    With the scan tool, erase the SKREEM DTCs

    NOTE: Perform the following test several times to ensure the DTC is current.

    Turn the ignition off.

    Wait 10 seconds.

    Turn the ignition on.

    With the scan tool, read the SKREEM DTCs.

    Does the scan tool display the DTC that was previously erased? 

    Yes 

    1. Go To  2).

    No 

    1. Go To  6).
  2. 2)  CHECKING FOR MULTIPLE KEYS 

    Are there multiple vehicle ignition keys available? 

    Yes 

    1. Go To  3).

    No 

    1. Go To  4).
  3. 3)  MULTIPLE KEY OPERATION 
    NOTE: Perform the following steps using one of the vehicle ignition keys. When finished, repeat the procedure using each of the other vehicle keys, one at a time.

    With the scan tool, erase the SKREEM DTCs.

    Turn the ignition off.

    Wait 10 seconds.

    Turn the ignition on.

    With the scan tool, read the SKREEM DTCs.

    Is the DTC present for all ignition keys? 

    Yes 

    1. Replace and program the Sentry Key Remote Entry Module in accordance with the Service Information.
    2. Perform SKREEM VERIFICATION TEST. (Refer to ELECTRICAL/VEHICLE THEFT SECURITY - STANDARD PROCEDURE) 

    No 

    1. Replace the ignition key(s) that cause the SKIM DTC.
    2. Perform SKREEM VERIFICATION TEST. (Refer to ELECTRICAL/VEHICLE THEFT SECURITY - STANDARD PROCEDURE) 
  4. 4)  REPROGRAM KEY 

    With the scan tool, attempt to reprogram the ignition key to the SKREEM.

    With the scan tool, erase the SKREEM DTCs.

    Wait 10 seconds.

    Turn the ignition on.

    With the scan tool, read the SKREEM DTCs.

    Does the DTC set again? 

    Yes 

    1. Replace and program the Sentry Key Remote Entry Module in accordance with the Service Information.
    2. Perform SKREEM VERIFICATION TEST. (Refer to ELECTRICAL/VEHICLE THEFT SECURITY - STANDARD PROCEDURE) 

    No 

    1. Test complete.
  5. 5)  PROGRAM NEW IGNITION KEY 

    Replace the ignition key with a new key.

    With the scan tool, program the new ignition key to the SKREEM.

    With the scan tool, erase the SKREEM DTCs.

    Turn the ignition off.

    Wait 10 seconds.

    Turn the ignition on.

    With the scan tool, read the SKREEM DTCs.

    Does the DTC set again? 

    Yes 

    1. Replace and program the Sentry Key Remote Entry Module in accordance with the Service Information.
    2. Perform SKREEM VERIFICATION TEST. (Refer to ELECTRICAL/VEHICLE THEFT SECURITY - STANDARD PROCEDURE) 

    No 

    1. Test complete.
  6. 6)  INTERMITTENT WIRING HARNESS PROBLEM 

    Turn the ignition off.

    NOTE: Check the following items:
    • Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires.
    • Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals.
    • Refer to any Technical Service Bulletins (TSB) that may apply.

    Were any problems found? 

    Yes 

    1. Repair wiring harness/connectors as necessary.
    2. Perform SKREEM VERIFICATION TEST. (Refer to ELECTRICAL/VEHICLE THEFT SECURITY - STANDARD PROCEDURE) 

    No 

    1. Test Complete.
scientia non olet · About LEMON Manuals