Diagnostic Test

1. Turn the ignition on.
2. With the scan tool, read ORC DTCs.

   Does the scan tool display active: U0173-LOST COMMUNICATION W/LEFT SIDE SATELLITE ACCELERATION SENSOR 1?

   Yes 

   • Go to step  2

   No 

   • Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. See DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

Fig 1: Checking Left Side Impact Sensor Circuits

Courtesy of CHRYSLER LLC

1. Disconnect the Left Side Impact Sensor 2 connector.
2. Disconnect the ORC C1 connector.
   WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
3. Measure the voltage of the (R17) Left Side Impact Sensor 2 Signal circuit and (R19) Sensor Ground circuit at the Left Side Impact Sensor 2 connector and ground.

   Is there any voltage present?

   Yes 

   • Repair the (R17, R19) Left Side Impact Sensor 2 circuits for a short to battery.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. See DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

   No 

   • Go to step  3

Fig 2: Checking Left Side Impact Sensor 2 Signal Circuit For A Short To Ground

Courtesy of CHRYSLER LLC

1. Measure the resistance of the (R17) Left Side Impact Sensor 2 Signal circuit between the Left Side Impact Sensor 2 connector and ground.

   Is the resistance below 100K Ohms?

   Yes 

   • Repair the (R17) Left Side Impact Sensor 2 Signal circuit for a short to ground.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. See DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

   No 

   • Go to step  4

Fig 3: Checking Left Side Impact Sensor 2 Circuits

Courtesy of CHRYSLER LLC

1. Measure the resistance between the (R17) Left Side Impact Sensor 2 Signal and (R19) Sensor Ground circuits at the Left Side Impact Sensor 2 connector.

   Is the resistance below 100K Ohms?

   Yes 

   • Repair the (R17, R19) Left Side Impact Sensor 2 circuits shorted together.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. See DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

   No 

   • Go to step  5

Fig 4: Check Left Side Impact Sensor 2 Ground Circuit For An Open Or High Resistance

Courtesy of CHRYSLER LLC

1. Connect the SRS Load Tool Kit 8443A to the ORC C1 connector.
2. Measure the resistance of the (R19) Left Side Impact Sensor 2 Ground circuit between the Left Side Impact Sensor 2 connector and the SRS Load Tool Kit 8443A.

   Is the resistance below 1 ohm?

   Yes 

   • Go to step  6

   No 

   • Repair the (R19) Left Side Impact Sensor 2 Ground circuit for an open or high resistance.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. See DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

Fig 5: Checking Left Side Impact Sensor 2 Circuit For An Open Or High Resistance

Courtesy of CHRYSLER LLC

1. Measure the resistance of the (R17) Left Side Impact Sensor 2 Signal circuit between the Left Side Impact Sensor 2 connector and the SRS Load Tool Kit 8443A.

   Is the resistance below 1 ohm?

   Yes 

   • Go to step  7

   No 

   • Repair the (R17) Left Side Impact Sensor 2 Signal circuit for an open or high resistance.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. See DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

1. Replace the Left Side Impact Sensor 2.
2. Reconnect the vehicle body harness to the impact sensor.
3. Remove any special tools or jumper wires and reconnect all previously disconnected components - except the Battery.
   WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
4. Connect the scan tool to the Data Link Connector - use the most current software available.
5. Use the scan tool and erase the stored codes in all airbag system modules.
6. Turn the Ignition Off, and wait 15 seconds before turning the Ignition On.
7. Wait one minute, and read active codes and if there are none present read the stored codes.

   Did the active Left Side Impact Sensor 2 DTC return?

   Yes 

   • Go to step  8

   No 

   • Repair is complete.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. See DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

If there are no possible causes remaining, view repair.

Repair 

• Replace the Occupant Restraint Controller in accordance with Service Instructions.
• Perform the RESTRAINTS SYSTEM VERIFICATION TEST. See DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .